1.12.1 SAMA5D2 Xplained Factory Installation to eMMC Log
Here is the complete debug output for booting and running from the SD card the image for initial factory system installation to the internal eMMC flash memory.
RomBOOT
Backup mode enabled
AT91Bootstrap 3.10.1-rc1-gitAUTOINC+1d013b417b-r0.tano1 (2022-08-06 00:11:04)
EEPROM: Loading AT24xx information ...
EEPROM: BoardName | [Revid] | VendorName
EEPROM: Using default information
EEPROM: Board sn: 0xd300000 revision: 0x248000
SD/MMC: Image: Read file u-boot.bin to 0x26f00000
MMC: ADMA supported
SD: Card Capacity: High or Extended
SD: Specification Version 3.0X
SD/MMC: Done to load image
<debug_uart>
U-Boot 2020.01-gitAUTOINC+af59b26c22-tano0.2 (Aug 06 2022 - 02:07:49 +0000)
CPU: SAMA5D27-CU
Crystal frequency: 12 MHz
CPU clock : 498 MHz
Master clock : 166 MHz
DRAM: 512 MiB
MMC: sdio-host@a0000000: 0, sdio-host@b0000000: 1
Loading Environment from MMC... OK
In: serial@f8020000
Out: serial@f8020000
Err: serial@f8020000
Net:
Warning: ethernet@f8008000 MAC addresses don't match:
Address in ROM is 00:10:a1:98:97:02
Address in environment is fc:c2:3d:02:f4:39
eth0: ethernet@f8008000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
MMC read: dev # 1, block # 512, count 256 ... 256 blocks read: OK
## Executing script at 21000000
Board name: sama5d2_xplained
Loading kernel fitImage...
switch to partitions #0, OK
mmc1 is current device
12546860 bytes read in 784 ms (15.3 MiB/s)
Force console to be enabled
Booting kernel 0x24000000#conf-at91-sama5d2_xplained.dtb...
## Loading kernel from FIT Image at 24000000 ...
Using 'conf-at91-sama5d2_xplained.dtb' configuration
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x24000118
Data Size: 4567560 Bytes = 4.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x22000000
Entry Point: 0x22000000
Hash algo: sha256
Hash value: 250ea354a19a928c5d40456071b49ca3c972373a34f04987ba277c8c63a09ba1
Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at 24000000 ...
Using 'conf-at91-sama5d2_xplained.dtb' configuration
Trying 'ramdisk-1' ramdisk subimage
Description: tanowrt-image-initramfs-swu-factory
Type: RAMDisk Image
Compression: uncompressed
Data Start: 0x2446640c
Data Size: 7932264 Bytes = 7.6 MiB
Architecture: ARM
OS: Linux
Load Address: 0x25000000
Entry Point: 0x25000000
Hash algo: sha256
Hash value: 7991e05f44db36fd8632db883843b372b24dc921aa12e9340d206d31e8bd4e66
Verifying Hash Integrity ... sha256+ OK
Loading ramdisk from 0x2446640c to 0x25000000
## Loading fdt from FIT Image at 24000000 ...
Using 'conf-at91-sama5d2_xplained.dtb' configuration
Trying 'fdt-at91-sama5d2_xplained.dtb' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x2445b438
Data Size: 44779 Bytes = 43.7 KiB
Architecture: ARM
Load Address: 0x23e00000
Hash algo: sha256
Hash value: 7afaaebdd0b2fe3b98ef4b716d5b279dfcfd9a928c4bc0874bd95c67fd05ce0c
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x2445b438 to 0x23e00000
Booting using the fdt blob at 0x23e00000
Loading Kernel Image
Loading Ramdisk to 3f3eb000, end 3fb7b968 ... OK
Loading Device Tree to 3f3dd000, end 3f3eaeea ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.78-tano-at91-standard-g046113c438-tano0.2.20.20.0.0 (oe-user@oe-host) (gcc version 10.3.0 (GCC)) #1 Fri Aug 5 23:46:16 UTC 2022
[ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Atmel SAMA5D2 Xplained
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x3e000000
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] random: get_random_bytes called from 0xc0a008e8 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram rootfstype=squashfs rootwait=1 earlyprintk panic=15
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 484220K/524288K available (7168K kernel code, 272K rwdata, 1296K rodata, 1024K init, 169K bss, 23684K reserved, 16384K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (8160 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 273 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 170 kB)
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C-310 ID prefetch enabled, offset 2 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 8 ways, 128 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x36020000
[ 0.000000] clocksource: timer@f800c000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 184217874325 ns
[ 0.000018] sched_clock: 32 bits at 10MHz, resolution 96ns, wraps every 206986376143ns
[ 0.000044] Switching to timer-based delay loop, resolution 96ns
[ 0.000367] clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 11513617062 ns
[ 0.000994] Console: colour dummy device 80x30
[ 0.001073] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.75 BogoMIPS (lpj=103750)
[ 0.001105] pid_max: default: 32768 minimum: 301
[ 0.001439] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001474] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.002844] CPU: Testing write buffer coherency: ok
[ 0.004205] Setting up static identity map for 0x20100000 - 0x20100060
[ 0.006199] devtmpfs: initialized
[ 0.023233] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 0.023693] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.023730] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.025382] pinctrl core: initialized pinctrl subsystem
[ 0.027460] NET: Registered protocol family 16
[ 0.030427] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.032498] cpuidle: using governor menu
[ 0.053008] AT91: PM: standby: standby, suspend: ulp0
[ 0.054184] atmel_tcb: probe of f800c000.timer failed with error -16
[ 0.072231] at_xdmac f0010000.dma-controller: 16 channels, mapped at 0x(ptrval)
[ 0.075117] at_xdmac f0004000.dma-controller: 16 channels, mapped at 0x(ptrval)
[ 0.076778] AT91: Detected SoC family: sama5d2
[ 0.076803] AT91: Detected SoC: sama5d27, revision 1
[ 0.077872] SCSI subsystem initialized
[ 0.078412] usbcore: registered new interface driver usbfs
[ 0.078532] usbcore: registered new interface driver hub
[ 0.078692] usbcore: registered new device driver usb
[ 0.079843] media: Linux media interface: v0.10
[ 0.079944] videodev: Linux video capture interface: v2.00
[ 0.080032] pps_core: LinuxPPS API ver. 1 registered
[ 0.080046] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.080199] PTP clock support registered
[ 0.080757] Advanced Linux Sound Architecture Driver Initialized.
[ 0.081811] Bluetooth: Core ver 2.22
[ 0.081951] NET: Registered protocol family 31
[ 0.081969] Bluetooth: HCI device and connection manager initialized
[ 0.082001] Bluetooth: HCI socket layer initialized
[ 0.082020] Bluetooth: L2CAP socket layer initialized
[ 0.082119] Bluetooth: SCO socket layer initialized
[ 0.083307] clocksource: Switched to clocksource timer@f800c000
[ 0.104627] NET: Registered protocol family 2
[ 0.105744] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[ 0.105868] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.105963] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.106048] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.106313] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.106361] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.106762] NET: Registered protocol family 1
[ 0.107944] RPC: Registered named UNIX socket transport module.
[ 0.107975] RPC: Registered udp transport module.
[ 0.107987] RPC: Registered tcp transport module.
[ 0.107998] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.108523] Trying to unpack rootfs image as initramfs...
[ 1.406666] Freeing initrd memory: 7748K
[ 1.408572] Initialise system trusted keyrings
[ 1.409185] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 1.409954] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.422465] Key type asymmetric registered
[ 1.422495] Asymmetric key parser 'x509' registered
[ 1.422547] io scheduler noop registered (default)
[ 1.422564] io scheduler mq-deadline registered
[ 1.422578] io scheduler kyber registered
[ 1.433449] pinctrl-at91-pio4 fc038000.pinctrl: atmel pinctrl initialized
[ 1.450222] brd: module loaded
[ 1.469719] loop: module loaded
[ 1.471191] atmel_usart_serial.0.auto: ttyS0 at MMIO 0xf8020000 (irq = 36, base_baud = 5187500) is a ATMEL_SERIAL
[ 2.048874] console [ttyS0] enabled
[ 2.054364] atmel_usart_serial.1.auto: ttyS1 at MMIO 0xfc008000 (irq = 41, base_baud = 5187500) is a ATMEL_SERIAL
[ 2.067390] at91_i2c fc018600.i2c: can't get DMA channel, continue without DMA support
[ 2.075352] at91_i2c fc018600.i2c: Using FIFO (16 data)
[ 2.080879] at91_i2c fc018600.i2c: AT91 i2c bus driver (hw version: 0x704).
[ 2.091043] atmel_spi f8000000.spi: DMA TX channel not available, SPI unable to use DMA
[ 2.099092] atmel_spi f8000000.spi: Atmel SPI Controller using PIO only
[ 2.105777] atmel_spi f8000000.spi: Using FIFO (16 data)
[ 2.112587] m25p80 spi0.0: at25df321a (4096 Kbytes)
[ 2.119552] atmel_spi f8000000.spi: Atmel SPI Controller version 0x311 at 0xf8000000 (irq 29)
[ 2.129392] libphy: Fixed MDIO Bus: probed
[ 2.134282] CAN device driver interface
[ 2.140252] m_can f8054000.can: m_can device registered (irq=39, version=31)
[ 2.153010] m_can fc050000.can: m_can device registered (irq=51, version=31)
[ 2.162063] libphy: MACB_mii_bus: probed
[ 2.275701] Micrel KSZ8081 or KSZ8091 f8008000.ethernet-ffffffff:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=f8008000.ethernet-ffffffff:01, irq=126)
[ 2.291315] macb f8008000.ethernet eth0: Cadence GEM rev 0x00020203 at 0xf8008000 irq 30 (fc:c2:3d:02:f4:39)
[ 2.301852] PPP generic driver version 2.4.2
[ 2.306681] PPP MPPE Compression module registered
[ 2.311403] NET: Registered protocol family 24
[ 2.315969] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.322427] ehci-atmel: EHCI Atmel driver
[ 2.330643] atmel-ehci 500000.ehci: EHCI Host Controller
[ 2.336035] atmel-ehci 500000.ehci: new USB bus registered, assigned bus number 1
[ 2.344317] atmel-ehci 500000.ehci: irq 20, io mem 0x00500000
[ 2.373416] atmel-ehci 500000.ehci: USB 2.0 started, EHCI 1.00
[ 2.379606] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 2.387866] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.395050] usb usb1: Product: EHCI Host Controller
[ 2.399871] usb usb1: Manufacturer: Linux 4.19.78-tano-at91-standard-g046113c438-tano0.2.20.20.0.0 ehci_hcd
[ 2.409647] usb usb1: SerialNumber: 500000.ehci
[ 2.415473] hub 1-0:1.0: USB hub found
[ 2.419274] hub 1-0:1.0: 3 ports detected
[ 2.424719] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.430892] ohci-atmel: OHCI Atmel driver
[ 2.436191] at91_ohci 400000.ohci: USB Host Controller
[ 2.441340] at91_ohci 400000.ohci: new USB bus registered, assigned bus number 2
[ 2.449205] at91_ohci 400000.ohci: irq 20, io mem 0x00400000
[ 2.454850] random: fast init done
[ 2.527793] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 2.536064] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.543212] usb usb2: Product: USB Host Controller
[ 2.548027] usb usb2: Manufacturer: Linux 4.19.78-tano-at91-standard-g046113c438-tano0.2.20.20.0.0 ohci_hcd
[ 2.557730] usb usb2: SerialNumber: at91
[ 2.563783] hub 2-0:1.0: USB hub found
[ 2.567583] hub 2-0:1.0: 3 ports detected
[ 2.573277] usbcore: registered new interface driver cdc_acm
[ 2.578974] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.587204] usbcore: registered new interface driver usb-storage
[ 2.593441] usbcore: registered new interface driver usbserial_generic
[ 2.599962] usbserial: USB Serial support registered for generic
[ 2.606028] usbcore: registered new interface driver ftdi_sio
[ 2.611760] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 2.620737] at91_rtc f80480b0.rtc: registered as rtc0
[ 2.625861] at91_rtc f80480b0.rtc: AT91 Real Time Clock driver.
[ 2.631978] i2c /dev entries driver
[ 2.637246] at91-reset f8048000.rstc: Starting after user reset
[ 2.645638] sama5d4_wdt f8048040.watchdog: initialized (timeout = 16 sec, nowayout = 0)
[ 2.654236] Bluetooth: HCI UART driver ver 2.3
[ 2.658619] Bluetooth: HCI UART protocol H4 registered
[ 2.663930] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 2.670279] usbcore: registered new interface driver btusb
[ 2.676397] sdhci: Secure Digital Host Controller Interface driver
[ 2.682503] sdhci: Copyright(c) Pierre Ossman
[ 2.687160] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.693630] sdhci-at91 a0000000.sdio-host: update clk mul to 39 as gck rate is 480000000 Hz and clk base is 12000000 Hz
[ 2.739586] mmc0: SDHCI controller on a0000000.sdio-host [a0000000.sdio-host] using ADMA
[ 2.748590] sdhci-at91 b0000000.sdio-host: update clk mul to 39 as gck rate is 480000000 Hz and clk base is 12000000 Hz
[ 2.761735] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.768217] atmel_aes f002c000.aes: version: 0x500
[ 2.777830] atmel_aes f002c000.aes: Atmel AES - Using dma0chan0, dma0chan1 for DMA transfers
[ 2.787095] atmel_sha f0028000.sha: version: 0x510
[ 2.791943] atmel_sha f0028000.sha: using dma0chan2 for DMA transfers
[ 2.803030] atmel_sha f0028000.sha: Atmel SHA1/SHA256/SHA224/SHA384/SHA512
[ 2.810895] atmel_tdes fc044000.tdes: version: 0x703
[ 2.816124] atmel_tdes fc044000.tdes: using dma0chan3, dma0chan4 for DMA transfers
[ 2.831818] atmel_tdes fc044000.tdes: Atmel DES/TDES
[ 2.837488] usbcore: registered new interface driver usbhid
[ 2.842995] usbhid: USB HID core driver
[ 2.854087] atmel-classd fc048000.classd: ASoC: Failed to create component debugfs directory
[ 2.862498] atmel-classd fc048000.classd: PWM modulation type is Differential, non-overlapping is enabled
[ 2.873196] atmel-classd fc048000.classd: atmel-classd-hifi <-> fc048000.classd mapping ok
[ 2.884421] atmel-pdmic f8018000.pdmic: ASoC: Failed to create component debugfs directory
[ 2.893738] atmel-pdmic f8018000.pdmic: atmel-pdmic-hifi <-> f8018000.pdmic mapping ok
[ 2.905109] u32 classifier
[ 2.907759] Actions configured
[ 2.911745] NET: Registered protocol family 10
[ 2.918341] Segment Routing with IPv6
[ 2.922083] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.929336] NET: Registered protocol family 17
[ 2.934016] Bridge firewalling registered
[ 2.937957] can: controller area network core (rev 20170425 abi 9)
[ 2.944391] NET: Registered protocol family 29
[ 2.948876] can: raw protocol (rev 20170425)
[ 2.953070] can: broadcast manager protocol (rev 20170425 t)
[ 2.958791] can: netlink gateway (rev 20170425) max_hops=1
[ 2.964863] Bluetooth: RFCOMM TTY layer initialized
[ 2.969709] Bluetooth: RFCOMM socket layer initialized
[ 2.974975] Bluetooth: RFCOMM ver 1.11
[ 2.978677] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.984000] Bluetooth: BNEP filters: protocol multicast
[ 2.989176] Bluetooth: BNEP socket layer initialized
[ 2.994139] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.000009] Bluetooth: HIDP socket layer initialized
[ 3.005035] l2tp_core: L2TP core driver, V2.0
[ 3.009336] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 3.014131] l2tp_netlink: L2TP netlink interface
[ 3.020781] Loading compiled-in X.509 certificates
[ 3.041652] at91_i2c f8028000.i2c: can't get DMA channel, continue without DMA support
[ 3.049679] at91_i2c f8028000.i2c: Using FIFO (16 data)
[ 3.056706] DCDC_REG1: supplied by regulator-dummy
[ 3.063449] mmc0: new DDR MMC card at address 0001
[ 3.071072] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB
[ 3.077627] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB
[ 3.085584] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB
[ 3.092031] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB, chardev (247:0)
[ 3.101154] DCDC_REG2: supplied by regulator-dummy
[ 3.109583] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 >
[ 3.114994] DCDC_REG3: supplied by regulator-dummy
[ 3.128497] LDO_REG1: supplied by regulator-dummy
[ 3.136649] LDO_REG2: supplied by regulator-dummy
[ 3.144745] LDO_REG3: supplied by regulator-dummy
[ 3.150392] VDD_LED: Bringing 2500000uV into 3300000-3300000uV
[ 3.160655] LDO_REG4: supplied by regulator-dummy
[ 3.170017] act8945a-charger act8945a-charger: DMA mask not set
[ 3.176502] act8945a-charger act8945a-charger: have been suspended
[ 3.185430] at91_i2c f8028000.i2c: AT91 i2c bus driver (hw version: 0x704).
[ 3.193007] at91_i2c fc028000.i2c: can't get DMA channel, continue without DMA support
[ 3.200959] at91_i2c fc028000.i2c: Using FIFO (16 data)
[ 3.208241] at24 2-0054: 256 byte 24c02 EEPROM, writable, 16 bytes/write
[ 3.215090] at91_i2c fc028000.i2c: AT91 i2c bus driver (hw version: 0x704).
[ 3.223033] sdhci-at91 b0000000.sdio-host: update clk mul to 39 as gck rate is 480000000 Hz and clk base is 12000000 Hz
[ 3.235219] sdhci-at91 b0000000.sdio-host: Linked as a consumer to regulator.3
[ 3.281803] mmc1: SDHCI controller on b0000000.sdio-host [b0000000.sdio-host] using ADMA
[ 3.291794] at91-sama5d2_adc fc030000.adc: Linked as a consumer to regulator.5
[ 3.304299] at91-sama5d2_adc fc030000.adc: setting up trigger as external_rising
[ 3.311677] at91-sama5d2_adc fc030000.adc: version: 800
[ 3.320123] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 3.328022] at91_rtc f80480b0.rtc: setting system clock to 2022-08-06 14:44:13 UTC (1659797053)
[ 3.337600] ALSA device list:
[ 3.340507] #0: CLASSD
[ 3.343022] #1: PDMIC @ sama5d2_xplained
[ 3.347868] atmel_usart_serial atmel_usart_serial.0.auto: using dma0chan7 for rx DMA transfers
[ 3.356593] atmel_usart_serial atmel_usart_serial.0.auto: using dma0chan8 for tx DMA transfers
[ 3.368261] Freeing unused kernel memory: 1024K
[ 3.372960] Run /init as init process
[ 3.420133] mmc1: new high speed SDHC card at address b368
[ 3.435521] mmcblk1: mmc1:b368 SDC 15.0 GiB
[ 3.455252] mmcblk1: p1
[ 4.253946] init: Console is alive
[ 4.257745] init: - watchdog -
[ 4.271686] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.278979] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.289302] init: - preinit -
[ 4.661848] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.699614] random: jshn: uninitialized urandom read (4 bytes read)
Press the [x] key to cancel automatic installation
Press the [r] key to install without last action (reboot/power off)
┌────────────────────────┐
│ │
│ Global configuration │
│ │
└────────────────────────┘
* Last action: poweroff
* Last action delay: 5 seconds
┌────────────────┐
│ │
│ Verification │
│ │
└────────────────┘
Checking required block devices...
════════════════════════════════════════════════════════════════════════════════
Block device /dev/mmcblk0 found
Block device /dev/mmcblk0boot0 found
Block device /dev/mmcblk0boot1 found
Block device /dev/mmcblk1 found
Block device /dev/mtdblock0 found
┌────────────────────┐
│ │
│ Pre-installation │
│ │
└────────────────────┘
Mounting filesystems...
════════════════════════════════════════════════════════════════════════════════
Mount 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk1p1
* Target: /mnt
* Filsystem: vfat
* Create target: yes
Executing command '/bin/mount -t vfat /dev/mmcblk1p1 /mnt'...
Executed '/bin/mount -t vfat /dev/mmcblk1p1 /mnt' with exit code 0
Mounted
Executing custom commands...
════════════════════════════════════════════════════════════════════════════════
Command 1
────────────────────────────────────────────────────────────
* Command: echo 0 > /sys/class/block/mmcblk0boot0/force_ro
* Required exit code : 0
Executing command 'echo 0 > /sys/class/block/mmcblk0boot0/force_ro'...
Executed 'echo 0 > /sys/class/block/mmcblk0boot0/force_ro' with exit code 0
Command 2
────────────────────────────────────────────────────────────
* Command: echo 0 > /sys/class/block/mmcblk0boot1/force_ro
* Required exit code : 0
Executing command 'echo 0 > /sys/class/block/mmcblk0boot1/force_ro'...
Executed 'echo 0 > /sys/class/block/mmcblk0boot1/force_ro' with exit code 0
Erasing block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0
* Block size: 512
* Count: 8192
Executing command '/bin/dd if=/dev/zero of=/dev/mmcblk0 bs=512 count=8192'...
8192+0 records in
8192+0 records out
Executed '/bin/dd if=/dev/zero of=/dev/mmcblk0 bs=512 count=8192' with exit code 0
Block device /dev/mmcblk0 erased
Block device 2
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0boot0
* Block size: 512
* Count: 2048
Executing command '/bin/dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=2048'...
2048+0 records in
2048+0 records out
Executed '/bin/dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=2048' with exit code 0
Block device /dev/mmcblk0boot0 erased
Block device 3
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0boot1
* Block size: 512
* Count: 2048
Executing command '/bin/dd if=/dev/zero of=/dev/mmcblk0boot1 bs=512 count=2048'...
2048+0 records in
2048+0 records out
Executed '/bin/dd if=/dev/zero of=/dev/mmcblk0boot1 bs=512 count=2048' with exit code 0
Block device /dev/mmcblk0boot1 erased
Creating partitions on block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0
* Label: msdos
* Block device size: 3850371072
Expression '$blkdev_size -ge 3221225472' is true, creating partitions
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mklabel msdos'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mklabel msdos' with exit code 0
Executing command '/usr/sbin/partprobe'...
Executed '/usr/sbin/partprobe' with exit code 0
Partition 1:
* Partition type: primary
* Filesystem type: fat16
* Start: 1MiB
* End: 9MiB
* Boot flag: 1
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary fat16 1MiB 9MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary fat16 1MiB 9MiB' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script set 1 boot on'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script set 1 boot on' with exit code 0
Partition 2:
* Partition type: primary
* Filesystem type: ext4
* Start: 9MiB
* End: 137MiB
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 9MiB 137MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 9MiB 137MiB' with exit code 0
Partition 3:
* Partition type: primary
* Start: 137MiB
* End: 1161MiB
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 137MiB 1161MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 137MiB 1161MiB' with exit code 0
Partition 4:
* Partition type: extended
* Start: 1161MiB
* End: 100%
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart extended 1161MiB 100%'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart extended 1161MiB 100%' with exit code 0
Partition 5:
* Partition type: logical
* Filesystem type: ext4
* Start: 1162MiB
* End: 1290MiB
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart logical ext4 1162MiB 1290MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart logical ext4 1162MiB 1290MiB' with exit code 0
Partition 6:
* Partition type: logical
* Start: 1291MiB
* End: 2315MiB
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart logical 1291MiB 2315MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart logical 1291MiB 2315MiB' with exit code 0
Partition 7:
* Partition type: logical
* Filesystem type: ext4
* Start: 2316MiB
* End: 100%
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart logical ext4 2316MiB 100%'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart logical ext4 2316MiB 100%' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script print'...
Model: MMC Q2J54A (sd/mmc)
Disk /dev/mmcblk0: 3850MB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Disk Flags:
Number Start End Size Type File system Flags
1 1049kB 9437kB 8389kB primary boot, lba
2 9437kB 144MB 134MB primary ext4
3 144MB 1217MB 1074MB primary
4 1217MB 3850MB 2633MB extended lba
5 1218MB 1353MB 134MB logical ext4
6 1354MB 2427MB 1074MB logical
7 2429MB 3850MB 1422MB logical ext4
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script print' with exit code 0
Executing command '/usr/sbin/partprobe'...
Executed '/usr/sbin/partprobe' with exit code 0
Created partitions on block device /dev/mmcblk0
Block device 2
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0
* Label: msdos
* Block device size: 3850371072
Expression '$blkdev_size -ge 419430400 -a $blkdev_size -lt 3221225472' is false, skipping partitions creation
Creating filesystems on block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0p1
* Filesystem type: fat
* Label: boot
Executing command '/usr/sbin/mkfs.fat -n boot /dev/mmcblk0p1'...
mkfs.fat 4.2 (2021-01-31)
mkfs.fat: Warning: lowercase labels might not work properly on some systems
Executed '/usr/sbin/mkfs.fat -n boot /dev/mmcblk0p1' with exit code 0
Created fat filesystem on /dev/mmcblk0p1
Block device 2
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0p7
* Filesystem type: ext4
* Label: rootfs_data
Executing command '/sbin/mkfs.ext4 -F -L rootfs_data /dev/mmcblk0p7'...
mke2fs 1.46.1 (9-Feb-2021)
/dev/mmcblk0p7 contains a ext4 file system labelled 'rootfs_data'
created on Sat Aug 6 14:33:23 2022
Discarding device blocks: done
Creating filesystem with 347136 4k blocks and 86944 inodes
Filesystem UUID: d6160c17-1b80-4907-868a-5a851c9c9767
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912
Allocating group tables: done
Writing inode tables: done
Creating journal (8192 blocks): done
Writing superblocks and filesystem accounting information: done
Executed '/sbin/mkfs.ext4 -F -L rootfs_data /dev/mmcblk0p7' with exit code 0
Created ext4 filesystem on /dev/mmcblk0p7
Writing images to block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0
Image 1:
* Image source: local
* Image URL: /mnt/u-boot-initial-env.bin
* Offset: 524288 bytes
Executing command '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=524288 seek=1'...
0+1 records in
0+1 records out
Executed '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=524288 seek=1' with exit code 0
Image 2:
* Image source: local
* Image URL: /mnt/u-boot-initial-env.bin
* Offset: 655360 bytes
Executing command '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=655360 seek=1'...
0+1 records in
0+1 records out
Executed '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=655360 seek=1' with exit code 0
Writed images to block device /dev/mmcblk0
Executing custom commands...
════════════════════════════════════════════════════════════════════════════════
Command 1
────────────────────────────────────────────────────────────
* Command: echo 1 > /sys/class/block/mmcblk0boot0/force_ro
* Required exit code : 0
Executing command 'echo 1 > /sys/class/block/mmcblk0boot0/force_ro'...
Executed 'echo 1 > /sys/class/block/mmcblk0boot0/force_ro' with exit code 0
Command 2
────────────────────────────────────────────────────────────
* Command: echo 1 > /sys/class/block/mmcblk0boot1/force_ro
* Required exit code : 0
Executing command 'echo 1 > /sys/class/block/mmcblk0boot1/force_ro'...
Executed 'echo 1 > /sys/class/block/mmcblk0boot1/force_ro' with exit code 0
┌────────────────┐
│ │
│ Installation │
│ │
└────────────────┘
Mounting filesystems...
════════════════════════════════════════════════════════════════════════════════
Mount 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0p1
* Target: /boot
* Filsystem: vfat
* Create target: yes
Executing command '/bin/mkdir -p "/boot"'...
Executed '/bin/mkdir -p "/boot"' with exit code 0
Target created
Executing command '/bin/mount -t vfat /dev/mmcblk0p1 /boot'...
Executed '/bin/mount -t vfat /dev/mmcblk0p1 /boot' with exit code 0
Mounted
┌─────────────────────┐
│ │
│ Installing images │
│ │
└─────────────────────┘
Installing image 1...
════════════════════════════════════════════════════════════════════════════════
* Type: swupdate
* Image source: local
* Image URL: /mnt/swu_install.swu
* Extra arguments: --no-bootloader-env
* Dry run: 1
* Install: 1
* Selections: ${SWU_SYSTEM_A_SELECTION} ${SWU_SYSTEM_B_SELECTION}
* Selections (expanded): tanowrt,system-a tanowrt,system-b
[dry] run for selection 'tanowrt,system-a'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.6.atmel0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on at91-sama5d2-xplained-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-a
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 4134
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2022-08-06-11:41:38-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for Atmel SAMA5D2 Xplained (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_a 2022-08-06-11:41:38-UTC: tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo in device : /dev/mmcblk0p3 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_a 4.19.78+gitAUTOINC+046113c438-tano0.2.20.20.0.0: fitImage-at91-sama5d2-xplained-emmc.ext4 in device : /dev/mmcblk0p2 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.atmel1: startup-at91-sama5d2-xplained-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2020.01-gitAUTOINC+af59b26c22-tano0.2: u-boot-at91-sama5d2-xplained-emmc.bin-emmc in device : /boot/u-boot.bin for handler rawfile
[WARN ] : SWUPDATE running : [check_field_string] : Configuration Key is empty!
[TRACE] : SWUPDATE running : [_parse_images] : Found Image at91bootstrap 3.10.1-rc1-gitAUTOINC+1d013b417b-r0.tano1: at91bootstrap.bin-emmc in device : /dev/mtdblock0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 0
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware at91-sama5d2-xplained-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 23875584
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo, 23875584 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename at91bootstrap.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 23477
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-at91-sama5d2-xplained-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 486607
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-at91-sama5d2-xplained-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2051
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-at91-sama5d2-xplained-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 6585344
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-at91-sama5d2-xplained-emmc.ext4, 6585344 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-at91-sama5d2-xplained-emmc.ext4 dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream at91bootstrap.bin-emmc dummy
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-at91-sama5d2-xplained-emmc.bin-emmc dummy
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-at91-sama5d2-xplained-emmc.img dummy
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 262144 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-a' [dry] run success
[dry] run for selection 'tanowrt,system-b'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.6.atmel0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on at91-sama5d2-xplained-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-b
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 4134
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2022-08-06-11:41:38-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for Atmel SAMA5D2 Xplained (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_b 2022-08-06-11:41:38-UTC: tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo in device : /dev/mmcblk0p6 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_b 4.19.78+gitAUTOINC+046113c438-tano0.2.20.20.0.0: fitImage-at91-sama5d2-xplained-emmc.ext4 in device : /dev/mmcblk0p5 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.atmel1: startup-at91-sama5d2-xplained-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2020.01-gitAUTOINC+af59b26c22-tano0.2: u-boot-at91-sama5d2-xplained-emmc.bin-emmc in device : /boot/u-boot.bin for handler rawfile
[WARN ] : SWUPDATE running : [check_field_string] : Configuration Key is empty!
[TRACE] : SWUPDATE running : [_parse_images] : Found Image at91bootstrap 3.10.1-rc1-gitAUTOINC+1d013b417b-r0.tano1: at91bootstrap.bin-emmc in device : /dev/mtdblock0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 1
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware at91-sama5d2-xplained-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 23875584
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo, 23875584 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename at91bootstrap.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 23477
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-at91-sama5d2-xplained-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 486607
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-at91-sama5d2-xplained-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2051
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-at91-sama5d2-xplained-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 6585344
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-at91-sama5d2-xplained-emmc.ext4, 6585344 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-at91-sama5d2-xplained-emmc.ext4 dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream at91bootstrap.bin-emmc dummy
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-at91-sama5d2-xplained-emmc.bin-emmc dummy
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-at91-sama5d2-xplained-emmc.img dummy
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 262144 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-b' [dry] run success
[install] run for selection 'tanowrt,system-a'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.6.atmel0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on at91-sama5d2-xplained-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-a
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 4134
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2022-08-06-11:41:38-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for Atmel SAMA5D2 Xplained (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_a 2022-08-06-11:41:38-UTC: tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo in device : /dev/mmcblk0p3 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_a 4.19.78+gitAUTOINC+046113c438-tano0.2.20.20.0.0: fitImage-at91-sama5d2-xplained-emmc.ext4 in device : /dev/mmcblk0p2 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.atmel1: startup-at91-sama5d2-xplained-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2020.01-gitAUTOINC+af59b26c22-tano0.2: u-boot-at91-sama5d2-xplained-emmc.bin-emmc in device : /boot/u-boot.bin for handler rawfile
[WARN ] : SWUPDATE running : [check_field_string] : Configuration Key is empty!
[TRACE] : SWUPDATE running : [_parse_images] : Found Image at91bootstrap 3.10.1-rc1-gitAUTOINC+1d013b417b-r0.tano1: at91bootstrap.bin-emmc in device : /dev/mtdblock0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 0
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware at91-sama5d2-xplained-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh preupdate tanowrt system-a command returned 0
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 23875584
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo, 23875584 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename at91bootstrap.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 23477
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-at91-sama5d2-xplained-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 486607
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-at91-sama5d2-xplained-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2051
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-at91-sama5d2-xplained-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 6585344
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-at91-sama5d2-xplained-emmc.ext4, 6585344 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-at91-sama5d2-xplained-emmc.ext4 raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream at91bootstrap.bin-emmc raw
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-at91-sama5d2-xplained-emmc.bin-emmc rawfile
[TRACE] : SWUPDATE running : [install_raw_file] : Installing file u-boot-at91-sama5d2-xplained-emmc.bin-emmc on /boot/u-boot.bin
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-at91-sama5d2-xplained-emmc.img raw
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 262144 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh postupdate-success tanowrt system-a command returned 0
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-a' [install] run success
[install] run for selection 'tanowrt,system-b'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.6.atmel0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on at91-sama5d2-xplained-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-b
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 4134
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2022-08-06-11:41:38-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for Atmel SAMA5D2 Xplained (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_b 2022-08-06-11:41:38-UTC: tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo in device : /dev/mmcblk0p6 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_b 4.19.78+gitAUTOINC+046113c438-tano0.2.20.20.0.0: fitImage-at91-sama5d2-xplained-emmc.ext4 in device : /dev/mmcblk0p5 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.atmel1: startup-at91-sama5d2-xplained-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2020.01-gitAUTOINC+af59b26c22-tano0.2: u-boot-at91-sama5d2-xplained-emmc.bin-emmc in device : /boot/u-boot.bin for handler rawfile
[WARN ] : SWUPDATE running : [check_field_string] : Configuration Key is empty!
[TRACE] : SWUPDATE running : [_parse_images] : Found Image at91bootstrap 3.10.1-rc1-gitAUTOINC+1d013b417b-r0.tano1: at91bootstrap.bin-emmc in device : /dev/mtdblock0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 1
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware at91-sama5d2-xplained-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh preupdate tanowrt system-b command returned 0
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 23875584
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo, 23875584 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream tanowrt-image-full-at91-sama5d2-xplained-emmc.squashfs-lzo raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename at91bootstrap.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 23477
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-at91-sama5d2-xplained-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 486607
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-at91-sama5d2-xplained-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2051
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-at91-sama5d2-xplained-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 6585344
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-at91-sama5d2-xplained-emmc.ext4, 6585344 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-at91-sama5d2-xplained-emmc.ext4 raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream at91bootstrap.bin-emmc raw
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-at91-sama5d2-xplained-emmc.bin-emmc rawfile
[TRACE] : SWUPDATE running : [install_raw_file] : Installing file u-boot-at91-sama5d2-xplained-emmc.bin-emmc on /boot/u-boot.bin
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-at91-sama5d2-xplained-emmc.img raw
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 262144 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh postupdate-success tanowrt system-b command returned 0
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-b' [install] run success
Executing custom commands...
════════════════════════════════════════════════════════════════════════════════
Command 1
────────────────────────────────────────────────────────────
* Command: umount /boot
* Required exit code : 0
Executing command 'umount /boot'...
Executed 'umount /boot' with exit code 0
┌─────────────────────┐
│ │
│ Post-installation │
│ │
└─────────────────────┘
Executing custom commands...
════════════════════════════════════════════════════════════════════════════════
Command 1
────────────────────────────────────────────────────────────
* Command: fw_setenv swu_active 0
* Required exit code : 0
Executing command 'fw_setenv swu_active 0'...
Executed 'fw_setenv swu_active 0' with exit code 0
Command 2
────────────────────────────────────────────────────────────
* Command: fw_setenv swu_upgrade_available 0
* Required exit code : 0
Executing command 'fw_setenv swu_upgrade_available 0'...
Executed 'fw_setenv swu_upgrade_available 0' with exit code 0
Command 3
────────────────────────────────────────────────────────────
* Command: fw_setenv swu_bootcount 0
* Required exit code : 0
Executing command 'fw_setenv swu_bootcount 0'...
Executed 'fw_setenv swu_bootcount 0' with exit code 0
┌────────────────────────────────────────────────┐
│ │
│ SUCCESS: Installation successfully completed │
│ │
└────────────────────────────────────────────────┘
Powering off in 5 seconds...
Powering off in 4 seconds...
Powering off in 3 seconds...
Powering off in 2 seconds...
Powering off in 1 seconds...
Powering off now...
[ 64.368061] reboot: Power down