1.12.3 SAMA5D2 Xplained Boot from SD Card Log
TanoWrt boot log from external SD card.
RomBOOT
Backup mode enabled
AT91Bootstrap 3.10.1-rc1-gitAUTOINC+1d013b417b-r0.tano1 (2022-08-05 22:14:13)
EEPROM: Loading AT24xx information ...
EEPROM: BoardName | [Revid] | VendorName
EEPROM: Using default information
EEPROM: Board sn: 0xd300000 revision: 0x248000
SD/MMC: Image: Read file u-boot.bin to 0x26f00000
MMC: ADMA supported
SD: Card Capacity: High or Extended
SD: Specification Version 3.0X
SD/MMC: Done to load image
<debug_uart>
U-Boot 2020.01-gitAUTOINC+af59b26c22-tano0.1 (Aug 06 2022 - 01:28:50 +0000)
CPU: SAMA5D27-CU
Crystal frequency: 12 MHz
CPU clock : 498 MHz
Master clock : 166 MHz
DRAM: 512 MiB
MMC: sdio-host@a0000000: 0, sdio-host@b0000000: 1
Loading Environment from MMC... OK
In: serial@f8020000
Out: serial@f8020000
Err: serial@f8020000
Net:
Warning: ethernet@f8008000 MAC addresses don't match:
Address in ROM is 00:10:a1:98:97:02
Address in environment is fc:c2:3d:02:f4:39
eth0: ethernet@f8008000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
MMC read: dev # 1, block # 512, count 256 ... 256 blocks read: OK
## Executing script at 21000000
Board name: sama5d2_xplained
Active system A
Loading kernel fitImage...
switch to partitions #0, OK
mmc1 is current device
4614332 bytes read in 285 ms (15.4 MiB/s)
Booting kernel 0x24000000#conf-at91-sama5d2_xplained.dtb...
## Loading kernel from FIT Image at 24000000 ...
Using 'conf-at91-sama5d2_xplained.dtb' configuration
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x24000118
Data Size: 4567560 Bytes = 4.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x22000000
Entry Point: 0x22000000
Hash algo: sha256
Hash value: ad2d840762b2497405013b4ae0b1662ace5e8fc582a13107405e7f06a3c04f5b
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 24000000 ...
Using 'conf-at91-sama5d2_xplained.dtb' configuration
Trying 'fdt-at91-sama5d2_xplained.dtb' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x2445b438
Data Size: 44779 Bytes = 43.7 KiB
Architecture: ARM
Load Address: 0x23e00000
Hash algo: sha256
Hash value: 7afaaebdd0b2fe3b98ef4b716d5b279dfcfd9a928c4bc0874bd95c67fd05ce0c
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x2445b438 to 0x23e00000
Booting using the fdt blob at 0x23e00000
Loading Kernel Image
Loading Device Tree to 3fb6e000, end 3fb7beea ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.78-tano-at91-standard-g046113c438-tano0.2.20.20.0.0 (oe-user@oe-host) (gcc version 10.3.0 (GCC)) #1 Fri Aug 5 22:20:36 UTC 2022
[ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Atmel SAMA5D2 Xplained
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x3e800000
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] random: get_random_bytes called from 0xc0a008e8 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/mmcblk1p3 ro rootfstype=squashfs rootwait rootfs_partition=3 rootfs_volume=3 earlyprintk panic=15
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 491972K/524288K available (7168K kernel code, 272K rwdata, 1296K rodata, 1024K init, 169K bss, 15932K reserved, 16384K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (8160 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 273 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 170 kB)
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C-310 ID prefetch enabled, offset 2 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 8 ways, 128 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x36020000
[ 0.000000] clocksource: timer@f800c000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 184217874325 ns
[ 0.000019] sched_clock: 32 bits at 10MHz, resolution 96ns, wraps every 206986376143ns
[ 0.000046] Switching to timer-based delay loop, resolution 96ns
[ 0.000360] clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 11513617062 ns
[ 0.000984] Console: colour dummy device 80x30
[ 0.001062] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.75 BogoMIPS (lpj=103750)
[ 0.001094] pid_max: default: 32768 minimum: 301
[ 0.001423] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001460] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.002822] CPU: Testing write buffer coherency: ok
[ 0.004190] Setting up static identity map for 0x20100000 - 0x20100060
[ 0.006186] devtmpfs: initialized
[ 0.023277] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 0.023730] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.023768] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.025428] pinctrl core: initialized pinctrl subsystem
[ 0.027511] NET: Registered protocol family 16
[ 0.030508] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.032573] cpuidle: using governor menu
[ 0.053096] AT91: PM: standby: standby, suspend: ulp0
[ 0.054271] atmel_tcb: probe of f800c000.timer failed with error -16
[ 0.072151] at_xdmac f0010000.dma-controller: 16 channels, mapped at 0x(ptrval)
[ 0.075032] at_xdmac f0004000.dma-controller: 16 channels, mapped at 0x(ptrval)
[ 0.076708] AT91: Detected SoC family: sama5d2
[ 0.076731] AT91: Detected SoC: sama5d27, revision 1
[ 0.077790] SCSI subsystem initialized
[ 0.078344] usbcore: registered new interface driver usbfs
[ 0.078461] usbcore: registered new interface driver hub
[ 0.078617] usbcore: registered new device driver usb
[ 0.079759] media: Linux media interface: v0.10
[ 0.079859] videodev: Linux video capture interface: v2.00
[ 0.079948] pps_core: LinuxPPS API ver. 1 registered
[ 0.079962] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.080011] PTP clock support registered
[ 0.080676] Advanced Linux Sound Architecture Driver Initialized.
[ 0.081737] Bluetooth: Core ver 2.22
[ 0.081873] NET: Registered protocol family 31
[ 0.081890] Bluetooth: HCI device and connection manager initialized
[ 0.081920] Bluetooth: HCI socket layer initialized
[ 0.081939] Bluetooth: L2CAP socket layer initialized
[ 0.082033] Bluetooth: SCO socket layer initialized
[ 0.083243] clocksource: Switched to clocksource timer@f800c000
[ 0.104671] NET: Registered protocol family 2
[ 0.105788] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[ 0.105915] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.106013] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.106099] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.106367] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.106420] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.106825] NET: Registered protocol family 1
[ 0.108001] RPC: Registered named UNIX socket transport module.
[ 0.108031] RPC: Registered udp transport module.
[ 0.108043] RPC: Registered tcp transport module.
[ 0.108055] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.110185] Initialise system trusted keyrings
[ 0.110705] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.111460] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.123919] Key type asymmetric registered
[ 0.123950] Asymmetric key parser 'x509' registered
[ 0.124002] io scheduler noop registered (default)
[ 0.124017] io scheduler mq-deadline registered
[ 0.124031] io scheduler kyber registered
[ 0.134841] pinctrl-at91-pio4 fc038000.pinctrl: atmel pinctrl initialized
[ 0.151513] brd: module loaded
[ 0.171054] loop: module loaded
[ 0.172500] atmel_usart_serial.0.auto: ttyS0 at MMIO 0xf8020000 (irq = 36, base_baud = 5187500) is a ATMEL_SERIAL
[ 0.744557] console [ttyS0] enabled
[ 0.749946] atmel_usart_serial.1.auto: ttyS1 at MMIO 0xfc008000 (irq = 41, base_baud = 5187500) is a ATMEL_SERIAL
[ 0.762950] at91_i2c fc018600.i2c: can't get DMA channel, continue without DMA support
[ 0.770908] at91_i2c fc018600.i2c: Using FIFO (16 data)
[ 0.776492] at91_i2c fc018600.i2c: AT91 i2c bus driver (hw version: 0x704).
[ 0.786601] atmel_spi f8000000.spi: DMA TX channel not available, SPI unable to use DMA
[ 0.794648] atmel_spi f8000000.spi: Atmel SPI Controller using PIO only
[ 0.801288] atmel_spi f8000000.spi: Using FIFO (16 data)
[ 0.808159] m25p80 spi0.0: at25df321a (4096 Kbytes)
[ 0.815139] atmel_spi f8000000.spi: Atmel SPI Controller version 0x311 at 0xf8000000 (irq 29)
[ 0.824945] libphy: Fixed MDIO Bus: probed
[ 0.829724] CAN device driver interface
[ 0.835825] m_can f8054000.can: m_can device registered (irq=39, version=31)
[ 0.848530] m_can fc050000.can: m_can device registered (irq=51, version=31)
[ 0.857590] libphy: MACB_mii_bus: probed
[ 0.955637] Micrel KSZ8081 or KSZ8091 f8008000.ethernet-ffffffff:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=f8008000.ethernet-ffffffff:01, irq=126)
[ 0.971251] macb f8008000.ethernet eth0: Cadence GEM rev 0x00020203 at 0xf8008000 irq 30 (fc:c2:3d:02:f4:39)
[ 0.981778] PPP generic driver version 2.4.2
[ 0.986566] PPP MPPE Compression module registered
[ 0.991296] NET: Registered protocol family 24
[ 0.995856] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.002312] ehci-atmel: EHCI Atmel driver
[ 1.010489] atmel-ehci 500000.ehci: EHCI Host Controller
[ 1.015890] atmel-ehci 500000.ehci: new USB bus registered, assigned bus number 1
[ 1.024044] atmel-ehci 500000.ehci: irq 20, io mem 0x00500000
[ 1.053327] atmel-ehci 500000.ehci: USB 2.0 started, EHCI 1.00
[ 1.059524] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 1.067791] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.074976] usb usb1: Product: EHCI Host Controller
[ 1.079799] usb usb1: Manufacturer: Linux 4.19.78-tano-at91-standard-g046113c438-tano0.2.20.20.0.0 ehci_hcd
[ 1.089573] usb usb1: SerialNumber: 500000.ehci
[ 1.095442] hub 1-0:1.0: USB hub found
[ 1.099219] hub 1-0:1.0: 3 ports detected
[ 1.104688] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.110858] ohci-atmel: OHCI Atmel driver
[ 1.116152] at91_ohci 400000.ohci: USB Host Controller
[ 1.121302] at91_ohci 400000.ohci: new USB bus registered, assigned bus number 2
[ 1.129357] at91_ohci 400000.ohci: irq 20, io mem 0x00400000
[ 1.207721] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 1.216004] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.223156] usb usb2: Product: USB Host Controller
[ 1.227972] usb usb2: Manufacturer: Linux 4.19.78-tano-at91-standard-g046113c438-tano0.2.20.20.0.0 ohci_hcd
[ 1.237675] usb usb2: SerialNumber: at91
[ 1.243483] hub 2-0:1.0: USB hub found
[ 1.247266] hub 2-0:1.0: 3 ports detected
[ 1.252965] usbcore: registered new interface driver cdc_acm
[ 1.258657] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.266830] usbcore: registered new interface driver usb-storage
[ 1.272991] usbcore: registered new interface driver usbserial_generic
[ 1.279588] usbserial: USB Serial support registered for generic
[ 1.285660] usbcore: registered new interface driver ftdi_sio
[ 1.291395] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 1.300435] at91_rtc f80480b0.rtc: registered as rtc0
[ 1.305565] at91_rtc f80480b0.rtc: AT91 Real Time Clock driver.
[ 1.311671] i2c /dev entries driver
[ 1.316948] at91-reset f8048000.rstc: Starting after wakeup
[ 1.325025] sama5d4_wdt f8048040.watchdog: initialized (timeout = 16 sec, nowayout = 0)
[ 1.333616] Bluetooth: HCI UART driver ver 2.3
[ 1.337999] Bluetooth: HCI UART protocol H4 registered
[ 1.343219] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 1.349641] usbcore: registered new interface driver btusb
[ 1.355743] sdhci: Secure Digital Host Controller Interface driver
[ 1.361857] sdhci: Copyright(c) Pierre Ossman
[ 1.366520] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.372922] sdhci-at91 a0000000.sdio-host: update clk mul to 39 as gck rate is 480000000 Hz and clk base is 12000000 Hz
[ 1.418919] mmc0: SDHCI controller on a0000000.sdio-host [a0000000.sdio-host] using ADMA
[ 1.427913] sdhci-at91 b0000000.sdio-host: update clk mul to 39 as gck rate is 480000000 Hz and clk base is 12000000 Hz
[ 1.441057] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.447546] atmel_aes f002c000.aes: version: 0x500
[ 1.457222] atmel_aes f002c000.aes: Atmel AES - Using dma0chan0, dma0chan1 for DMA transfers
[ 1.466505] atmel_sha f0028000.sha: version: 0x510
[ 1.471352] atmel_sha f0028000.sha: using dma0chan2 for DMA transfers
[ 1.482494] atmel_sha f0028000.sha: Atmel SHA1/SHA256/SHA224/SHA384/SHA512
[ 1.490329] atmel_tdes fc044000.tdes: version: 0x703
[ 1.495558] atmel_tdes fc044000.tdes: using dma0chan3, dma0chan4 for DMA transfers
[ 1.511301] atmel_tdes fc044000.tdes: Atmel DES/TDES
[ 1.516984] usbcore: registered new interface driver usbhid
[ 1.522488] usbhid: USB HID core driver
[ 1.533647] atmel-classd fc048000.classd: ASoC: Failed to create component debugfs directory
[ 1.542063] atmel-classd fc048000.classd: PWM modulation type is Differential, non-overlapping is enabled
[ 1.552737] atmel-classd fc048000.classd: atmel-classd-hifi <-> fc048000.classd mapping ok
[ 1.563949] atmel-pdmic f8018000.pdmic: ASoC: Failed to create component debugfs directory
[ 1.573158] atmel-pdmic f8018000.pdmic: atmel-pdmic-hifi <-> f8018000.pdmic mapping ok
[ 1.584497] u32 classifier
[ 1.587140] Actions configured
[ 1.591129] NET: Registered protocol family 10
[ 1.597724] Segment Routing with IPv6
[ 1.601470] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 1.608737] NET: Registered protocol family 17
[ 1.613407] Bridge firewalling registered
[ 1.617355] can: controller area network core (rev 20170425 abi 9)
[ 1.623778] NET: Registered protocol family 29
[ 1.628262] can: raw protocol (rev 20170425)
[ 1.632460] can: broadcast manager protocol (rev 20170425 t)
[ 1.638178] can: netlink gateway (rev 20170425) max_hops=1
[ 1.644243] Bluetooth: RFCOMM TTY layer initialized
[ 1.649081] Bluetooth: RFCOMM socket layer initialized
[ 1.654343] Bluetooth: RFCOMM ver 1.11
[ 1.658042] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.663363] Bluetooth: BNEP filters: protocol multicast
[ 1.668538] Bluetooth: BNEP socket layer initialized
[ 1.673499] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.679371] Bluetooth: HIDP socket layer initialized
[ 1.684404] l2tp_core: L2TP core driver, V2.0
[ 1.688707] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.693499] l2tp_netlink: L2TP netlink interface
[ 1.700199] Loading compiled-in X.509 certificates
[ 1.720914] at91_i2c f8028000.i2c: can't get DMA channel, continue without DMA support
[ 1.728951] at91_i2c f8028000.i2c: Using FIFO (16 data)
[ 1.735981] DCDC_REG1: supplied by regulator-dummy
[ 1.742651] mmc0: new DDR MMC card at address 0001
[ 1.750362] mmcblk0: mmc0:0001 Q2J54A 3.59 GiB
[ 1.756901] mmcblk0boot0: mmc0:0001 Q2J54A partition 1 16.0 MiB
[ 1.764861] mmcblk0boot1: mmc0:0001 Q2J54A partition 2 16.0 MiB
[ 1.771308] mmcblk0rpmb: mmc0:0001 Q2J54A partition 3 512 KiB, chardev (247:0)
[ 1.780114] DCDC_REG2: supplied by regulator-dummy
[ 1.786709] mmcblk0: p1 p2
[ 1.795508] DCDC_REG3: supplied by regulator-dummy
[ 1.801205] random: fast init done
[ 1.806788] LDO_REG1: supplied by regulator-dummy
[ 1.814874] LDO_REG2: supplied by regulator-dummy
[ 1.822973] LDO_REG3: supplied by regulator-dummy
[ 1.828707] VDD_LED: Bringing 2500000uV into 3300000-3300000uV
[ 1.838912] LDO_REG4: supplied by regulator-dummy
[ 1.848322] act8945a-charger act8945a-charger: DMA mask not set
[ 1.854833] act8945a-charger act8945a-charger: have been suspended
[ 1.863755] at91_i2c f8028000.i2c: AT91 i2c bus driver (hw version: 0x704).
[ 1.871332] at91_i2c fc028000.i2c: can't get DMA channel, continue without DMA support
[ 1.879296] at91_i2c fc028000.i2c: Using FIFO (16 data)
[ 1.886618] at24 2-0054: 256 byte 24c02 EEPROM, writable, 16 bytes/write
[ 1.893473] at91_i2c fc028000.i2c: AT91 i2c bus driver (hw version: 0x704).
[ 1.901424] sdhci-at91 b0000000.sdio-host: update clk mul to 39 as gck rate is 480000000 Hz and clk base is 12000000 Hz
[ 1.913610] sdhci-at91 b0000000.sdio-host: Linked as a consumer to regulator.3
[ 1.960139] mmc1: SDHCI controller on b0000000.sdio-host [b0000000.sdio-host] using ADMA
[ 1.970180] at91-sama5d2_adc fc030000.adc: Linked as a consumer to regulator.5
[ 1.982560] at91-sama5d2_adc fc030000.adc: setting up trigger as external_rising
[ 1.989990] at91-sama5d2_adc fc030000.adc: version: 800
[ 1.998423] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 2.006281] at91_rtc f80480b0.rtc: setting system clock to 2022-08-06 04:37:50 UTC (1659760670)
[ 2.015856] ALSA device list:
[ 2.018760] #0: CLASSD
[ 2.021275] #1: PDMIC @ sama5d2_xplained
[ 2.026119] atmel_usart_serial atmel_usart_serial.0.auto: using dma0chan7 for rx DMA transfers
[ 2.034848] atmel_usart_serial atmel_usart_serial.0.auto: using dma0chan8 for tx DMA transfers
[ 2.044108] Waiting for root device /dev/mmcblk1p3...
[ 2.081783] mmc1: new high speed SDHC card at address b368
[ 2.089996] mmcblk1: mmc1:b368 SDC 15.0 GiB
[ 2.099729] mmcblk1: p1 p2 p3 p4 < p5 p6 p7 >
[ 2.139136] VFS: Mounted root (squashfs filesystem) readonly on device 179:27.
[ 2.150200] devtmpfs: mounted
[ 2.156210] Freeing unused kernel memory: 1024K
[ 2.160873] Run /sbin/init as init process
[ 2.329187] init: Console is alive
[ 2.332986] init: - watchdog -
[ 2.963883] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.984434] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.002454] init: - preinit -
[ 3.568080] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.604653] random: jshn: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.912069] overlay-resize: Root device mmcblk1
[ 7.188550] overlay-resize: Overlay partition /dev/mmcblk1p7 (disk /dev/mmcblk1)
[ 7.302375] overlay-resize: EXT4 filesystem
[ 7.488027] overlay-resize: Filesystem successfully checked (0)
[ 9.485664] overlay-resize: Partition 4 resized to fill its full disk size
[ 9.730070] overlay-resize: Partition 7 resized to fill its full disk size
[ 9.738039] overlay-resize: Partition /dev/mmcblk1p7 end sector 1925119 -> 100% (31512448)
[ 9.746605] overlay-resize: Resizing filesystem on partition /dev/mmcblk1p7...
[ 78.149178] overlay-resize: Filesystem resized
[ 78.331912] SWUPDATE: AT91Bootstrap version 3.10.1-rc1-gitAUTOINC+1d013b417b-r0.tano1
[ 78.465086] SWUPDATE: U-Boot version 2020.01-gitAUTOINC+af59b26c22-tano0.1
[ 78.551760] SWUPDATE: U-Boot startup version 1.0.0-tano1.atmel0
[ 78.575395] SWUPDATE: Kernel version 4.19.78-tano-at91-standard-g046113c438-tano0.2.20.20.0.0
[ 78.605486] SWUPDATE: Read-only filesystem version 2022-08-06-01-32-36-UTC
[ 78.769171] mount_root: /dev/mmcblk1p1: p1, rw, start 1048576, size 8388608
[ 78.782962] mount_root: /dev/mmcblk1p2: p2, rw, start 9437184, size 67108864
[ 78.790493] mount_root: /dev/mmcblk1p3: p3, rw, start 76546048, size 402653184 [rootfs]
[ 78.800099] mount_root: /dev/mmcblk1p4: p4, rw, start 480246784, size 1024
[ 78.813752] mount_root: /dev/mmcblk1p5: p5, rw, start 480247808, size 67108864
[ 78.823436] mount_root: /dev/mmcblk1p6: p6, rw, start 548405248, size 402653184
[ 78.836919] mount_root: /dev/mmcblk1p7: p7, rw, start 952107008, size 15182331904 [overlay]
[ 78.845488] mount_root: root filesystem on the /dev/mmcblk1p3 partition of /dev/mmcblk1 (rw) device
[ 78.879518] mount_root: founded suitable overlay partition /dev/mmcblk1p7
[ 78.887351] mount_root: loading kmods from internal overlay
[ 79.012311] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 79.022676] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 79.073740] random: crng init done
[ 79.320683] EXT4-fs (mmcblk1p7): mounted filesystem with ordered data mode. Opts: (null)
[ 79.329221] block: attempting to load /tmp/ext4_cfg/upper/etc/config/fstab
[ 79.337628] block: unable to load configuration (fstab: Entry not found)
[ 79.344564] block: attempting to load /tmp/ext4_cfg/etc/config/fstab
[ 79.351103] block: unable to load configuration (fstab: Entry not found)
[ 79.357964] block: attempting to load /etc/config/fstab
[ 79.371339] block: extroot: not configured
[ 79.459979] EXT4-fs (mmcblk1p7): mounted filesystem with ordered data mode. Opts: (null)
[ 79.661640] block: attempting to load /tmp/ext4_cfg/upper/etc/config/fstab
[ 79.668800] block: unable to load configuration (fstab: Entry not found)
[ 79.675658] block: attempting to load /tmp/ext4_cfg/etc/config/fstab
[ 79.682191] block: unable to load configuration (fstab: Entry not found)
[ 79.689053] block: attempting to load /etc/config/fstab
[ 79.694959] block: extroot: not configured
[ 79.701986] mount_root: overlay filesystem has not been fully initialized yet
[ 79.716112] mount_root: switching to ext4 overlay
[ 80.786157] Root filesystem mounted
[ 82.243912] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 82.303217] procd: - watchdog -
[ 82.320541] procd: - ubus -
[ 82.387196] procd: - init -
Please press Enter to activate this console.
[ 85.505847] kmodloader: loading kernel modules from /etc/modules.d/*
[ 85.541525] tun: Universal TUN/TAP device driver, 1.6
[ 85.639117] atmel_usba_udc 300000.gadget: MMIO registers at [mem 0xfc02c000-0xfc02c3ff] mapped at 7996a97f
[ 85.648902] atmel_usba_udc 300000.gadget: FIFO at [mem 0x00300000-0x003fffff] mapped at 56cb895e
[ 85.695645] usbcore: registered new interface driver cdc_wdm
[ 85.744284] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 86.336710] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 86.344081] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 86.352630] cfg80211: failed to load regulatory.db
[ 86.365381] cryptodev: loading out-of-tree module taints kernel.
[ 86.385096] cryptodev: driver 1.12 loaded.
[ 86.390528] gre: GRE over IPv4 demultiplexor driver
[ 86.500053] PPTP driver version 0.8.5
[ 86.541004] xt_time: kernel timezone is +0300
[ 86.556644] usbcore: registered new interface driver cdc_ncm
[ 86.629010] usbcore: registered new interface driver qmi_wwan
[ 86.654117] usbcore: registered new interface driver cdc_mbim
[ 86.679385] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 98.320242] udevd[1398]: starting version 3.2.10
[ 98.840912] udevd[1398]: starting eudev-3.2.10
[ 144.497976] br-lan: port 1(eth0) entered blocking state
[ 144.503151] br-lan: port 1(eth0) entered disabled state
[ 144.509032] device eth0 entered promiscuous mode
[ 144.598189] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 146.901627] macb f8008000.ethernet eth0: link up (100/Full)
[ 146.923544] br-lan: port 1(eth0) entered blocking state
[ 146.928720] br-lan: port 1(eth0) entered forwarding state
[ 146.983620] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 168.816821] using random self ethernet address
[ 168.821210] using random host ethernet address
[ 168.827335] usb0: HOST MAC fa:62:ca:04:fd:92
[ 168.831693] usb0: MAC 62:4e:08:3c:10:5a
[ 168.835630] using random self ethernet address
[ 168.840004] using random host ethernet address
[ 168.844601] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[ 168.851151] g_ether gadget: g_ether ready
[ 168.859512] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
[ 169.032803] g_ether gadget: high-speed config #2: RNDIS
[ 169.038352] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready
tanowrt login: root
Password:
_______ __ __ _
|__ __| \ \ / / | | Embedded Linux Distribution
| | __ _ _ __ __\ \ /\ / / __| |_ by Tano Systems
| |/ _` | '_ \ / _ \ \/ \/ / '__| __|
| | (_| | | | | (_) \ /\ /| | | |_ (c) 2018-2022 Tano Systems LLC
|_|\__,_|_| |_|\___/ \/ \/ |_| \__| https://tano-systems.com
Board: Atmel SAMA5D2 Xplained (SD)
Release: 2021.06
Revision: 1697259fede8226e553eacab3562cc37fd6d7bd2
2022-08-06 01:32:36 UTC
[root@tanowrt ~]#