1.12.3 Boardcon EM3566 Factory Installation to eMMC Log
Here is the complete debug output for booting and running from the microSD card the image for initial factory system installation to the internal eMMC flash memory.
DDR Version V1.13 20220218
ln
ddrconfig:7
LP4 MR14:0x4d
LPDDR4, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
tdqss: cs0 dqs0: 554ps, dqs1: 434ps, dqs2: 506ps, dqs3: 482ps,
tdqss: cs1 dqs0: 554ps, dqs1: 458ps, dqs2: 506ps, dqs3: 458ps,
change to: 324MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
change to: 528MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x63
change to: 780MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58
change to: 1056MHz(final freq)
PHY drv:clk:38,ca:38,DQ:30,odt:60
vrefinner:16%, vrefout:29%
dram drv:40,odt:80
vref_ca:00000068
clk skew:0x15
cs 0:
the read training result:
DQS0:0x34, DQS1:0x34, DQS2:0x39, DQS3:0x37,
min : 0xc 0xd 0xb 0x8 0x2 0x5 0x6 0x3 , 0x5 0x5 0x3 0x2 0x5 0x8 0xa 0x5 ,
0x9 0xa 0xa 0x7 0x6 0x0 0x8 0x7 , 0x9 0x7 0x7 0x1 0x7 0x7 0x8 0xa ,
mid :0x27 0x27 0x27 0x24 0x1d 0x20 0x22 0x1e ,0x20 0x20 0x1f 0x1e 0x21 0x23 0x24 0x21 ,
0x26 0x27 0x25 0x24 0x22 0x1d 0x23 0x24 ,0x26 0x23 0x23 0x1e 0x23 0x24 0x25 0x26 ,
max :0x43 0x41 0x43 0x41 0x38 0x3b 0x3e 0x3a ,0x3c 0x3c 0x3c 0x3b 0x3d 0x3e 0x3f 0x3e ,
0x43 0x44 0x40 0x41 0x3f 0x3b 0x3f 0x41 ,0x43 0x3f 0x40 0x3b 0x40 0x42 0x43 0x43 ,
range:0x37 0x34 0x38 0x39 0x36 0x36 0x38 0x37 ,0x37 0x37 0x39 0x39 0x38 0x36 0x35 0x39 ,
0x3a 0x3a 0x36 0x3a 0x39 0x3b 0x37 0x3a ,0x3a 0x38 0x39 0x3a 0x39 0x3b 0x3b 0x39 ,
the write training result:
DQS0:0x5f, DQS1:0x4f, DQS2:0x59, DQS3:0x56,
min :0x91 0x93 0x94 0x93 0x89 0x8b 0x8e 0x8b 0x8d ,0x7c 0x7d 0x7d 0x7c 0x7f 0x82 0x80 0x80 0x80 ,
0x89 0x8d 0x8b 0x89 0x87 0x84 0x87 0x8a 0x8a ,0x87 0x86 0x85 0x82 0x87 0x88 0x87 0x88 0x85 ,
mid :0xae 0xaf 0xb0 0xae 0xa5 0xa7 0xa9 0xa6 0xa9 ,0x99 0x99 0x99 0x99 0x9a 0x9d 0x9b 0x9b 0x9b ,
0xa5 0xa8 0xa6 0xa4 0xa2 0x9f 0xa2 0xa4 0xa5 ,0xa3 0xa2 0xa1 0x9f 0xa3 0xa5 0xa3 0xa5 0xa2 ,
max :0xcb 0xcc 0xcc 0xc9 0xc2 0xc4 0xc5 0xc2 0xc5 ,0xb7 0xb5 0xb5 0xb6 0xb6 0xb8 0xb7 0xb6 0xb6 ,
0xc1 0xc4 0xc2 0xc0 0xbe 0xbb 0xbd 0xbe 0xc0 ,0xc0 0xbf 0xbe 0xbc 0xc0 0xc2 0xbf 0xc2 0xbf ,
range:0x3a 0x39 0x38 0x36 0x39 0x39 0x37 0x37 0x38 ,0x3b 0x38 0x38 0x3a 0x37 0x36 0x37 0x36 0x36 ,
0x38 0x37 0x37 0x37 0x37 0x37 0x36 0x34 0x36 ,0x39 0x39 0x39 0x3a 0x39 0x3a 0x38 0x3a 0x3a ,
cs 1:
the read training result:
DQS0:0x36, DQS1:0x35, DQS2:0x36, DQS3:0x36,
min : 0xc 0xe 0xb 0x9 0x2 0x4 0x7 0x4 , 0x4 0x4 0x2 0x2 0x4 0x5 0x8 0x4 ,
0x9 0xb 0xb 0x8 0x7 0x2 0x8 0x7 , 0x9 0x8 0x7 0x2 0x8 0x8 0x8 0xb ,
mid :0x28 0x29 0x28 0x26 0x1e 0x20 0x23 0x20 ,0x21 0x20 0x1f 0x1e 0x21 0x22 0x24 0x21 ,
0x24 0x26 0x23 0x22 0x21 0x1d 0x21 0x21 ,0x25 0x23 0x22 0x1d 0x23 0x24 0x24 0x26 ,
max :0x44 0x44 0x45 0x43 0x3b 0x3c 0x40 0x3c ,0x3e 0x3c 0x3c 0x3b 0x3e 0x40 0x41 0x3f ,
0x3f 0x41 0x3c 0x3c 0x3c 0x38 0x3b 0x3c ,0x41 0x3e 0x3d 0x38 0x3f 0x41 0x41 0x41 ,
range:0x38 0x36 0x3a 0x3a 0x39 0x38 0x39 0x38 ,0x3a 0x38 0x3a 0x39 0x3a 0x3b 0x39 0x3b ,
0x36 0x36 0x31 0x34 0x35 0x36 0x33 0x35 ,0x38 0x36 0x36 0x36 0x37 0x39 0x39 0x36 ,
the write training result:
DQS0:0x5f, DQS1:0x4f, DQS2:0x59, DQS3:0x56,
min :0x91 0x94 0x94 0x93 0x8a 0x8b 0x8e 0x8c 0x8e ,0x80 0x80 0x7f 0x7f 0x81 0x85 0x84 0x82 0x82 ,
0x89 0x8d 0x8b 0x8a 0x88 0x84 0x88 0x8a 0x8b ,0x82 0x82 0x82 0x7f 0x83 0x85 0x84 0x86 0x82 ,
mid :0xae 0xb0 0xb0 0xaf 0xa6 0xa7 0xaa 0xa7 0xaa ,0x9d 0x9c 0x9c 0x9c 0x9d 0xa0 0x9f 0x9e 0x9e ,
0xa6 0xa9 0xa7 0xa6 0xa4 0xa0 0xa3 0xa5 0xa6 ,0x9f 0x9f 0x9f 0x9c 0xa0 0xa2 0xa0 0xa2 0x9f ,
max :0xcc 0xcc 0xcd 0xcb 0xc2 0xc4 0xc6 0xc3 0xc6 ,0xbb 0xb9 0xb9 0xb9 0xba 0xbc 0xbb 0xbb 0xbb ,
0xc3 0xc6 0xc3 0xc2 0xc0 0xbc 0xbe 0xc1 0xc2 ,0xbd 0xbc 0xbc 0xb9 0xbd 0xbf 0xbc 0xbf 0xbc ,
range:0x3b 0x38 0x39 0x38 0x38 0x39 0x38 0x37 0x38 ,0x3b 0x39 0x3a 0x3a 0x39 0x37 0x37 0x39 0x39 ,
0x3a 0x39 0x38 0x38 0x38 0x38 0x36 0x37 0x37 ,0x3b 0x3a 0x3a 0x3a 0x3a 0x3a 0x38 0x39 0x3a ,
CA Training result:
cs:0 min :0x49 0x40 0x44 0x34 0x42 0x34 0x40 ,0x4a 0x3e 0x45 0x36 0x41 0x34 0x43 ,
cs:0 mid :0x84 0x83 0x7e 0x7b 0x7b 0x79 0x6b ,0x84 0x82 0x7e 0x7a 0x7d 0x79 0x6f ,
cs:0 max :0xbf 0xc7 0xb9 0xc2 0xb4 0xbf 0x96 ,0xbf 0xc7 0xb7 0xbf 0xba 0xbe 0x9b ,
cs:0 range:0x76 0x87 0x75 0x8e 0x72 0x8b 0x56 ,0x75 0x89 0x72 0x89 0x79 0x8a 0x58 ,
cs:1 min :0x4e 0x43 0x4a 0x39 0x46 0x39 0x3a ,0x4d 0x40 0x46 0x39 0x47 0x36 0x38 ,
cs:1 mid :0x88 0x87 0x84 0x7f 0x80 0x7f 0x70 ,0x87 0x85 0x80 0x7d 0x81 0x7a 0x70 ,
cs:1 max :0xc3 0xcc 0xbe 0xc6 0xbb 0xc6 0xa7 ,0xc1 0xca 0xbb 0xc2 0xbb 0xbf 0xa9 ,
cs:1 range:0x75 0x89 0x74 0x8d 0x75 0x8d 0x6d ,0x74 0x8a 0x75 0x89 0x74 0x89 0x71 ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-gitAUTOINC+e3ca3c3805_fe66a9be19-tano8 (Jul 20 2022 - 11:45:49)
unknown raw ID 3f6c928
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
spl: partition error
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(fe4f274c06...) + OK
## Checking uboot 0x00a00000 ... sha256(0c5e8aae67...) + OK
## Checking fdt 0x00b0d3a0 ... sha256(14c4d4c732...) + OK
## Checking atf-2 0x00068000 ... sha256(8d44036095...) + OK
## Checking atf-3 0xfdcd0000 ... sha256(e410275b51...) + OK
## Checking atf-4 0xfdcc9000 ... sha256(990c53fc01...) + OK
## Checking atf-5 0x00066000 ... sha256(315a4195a9...) + OK
## Checking optee 0x08400000 ... sha256(b8cddafab0...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 376.894 ms
INFO: Preloader serial: 4
I/TC:
I/TC: Start rockchip platform init
I/TC: Rockchip release version: 1.0
I/TC: OP-TEE version: 3.6.0-307-g0b06ae94 #1 Fri May 7 01:52:27 UTC 2021 aarch64
I/TC: Initialized
U-Boot 2017.09-gitAUTOINC+e3ca3c3805_fe66a9be19-tano8 (Jul 20 2022 - 11:45:30 +0000)
Model: Rockchip RK3568 Evaluation Board
PreSerial: 4, raw, 0xfe680000
DRAM: 2 GiB
Sysmem: init
Relocation Offset: 7d36c000
Relocation fdt: 7b9e7088 - 7b9fece8
CR: M/C/I
io-domain: OK
Failed to get scmi clk dev
NAND: nand_base: timeout while waiting for chip to become ready
nand_base: No NAND device found
0 MiB
mtd_blk: no mmc device at slot 1
dwmmc@fe2b0000: 1 (SD), dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): <NULL> <NULL>
Use emmc as default boot media
MMC0: HS200, 200Mhz
PartType: EFI
MMC: Model: Rockchip RK3568 Evaluation Board
rockchip_set_serialno: could not find efuse/otp device
No misc partition
boot mode: None
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 816000 KHz
dpll 528000 KHz
gpll 1188000 KHz
cpll 1000000 KHz
npll 1200000 KHz
vpll 24000 KHz
hpll 24000 KHz
ppll 200000 KHz
armclk 816000 KHz
aclk_bus 150000 KHz
pclk_bus 100000 KHz
aclk_top_high 300000 KHz
aclk_top_low 200000 KHz
hclk_top 150000 KHz
pclk_top 100000 KHz
aclk_perimid 300000 KHz
hclk_perimid 150000 KHz
pclk_pmu 100000 KHz
No misc partition
Net: No ethernet found.
Hit key to stop autoboot('CTRL+C'): 0
switch to partitions #0, OK
mmc1 is current device
MMC read: dev # 1, block # 7936, count 128 ... 128 blocks read: OK
## Executing script at 00c00000
Board name: evb_rk3568
Loading kernel fitImage...
switch to partitions #0, OK
mmc1 is current device
18675244 bytes read in 1579 ms (11.3 MiB/s)
Force console to be enabled
Booting kernel 0x04080000#conf-rockchip_boardcon-em3566.dtb...
Fdt Ramdisk skip relocation
No misc partition
## Loading kernel from FIT Image at 04080000 ...
Using 'conf-rockchip_boardcon-em3566.dtb' configuration
## Verified-boot: 0
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x04080114
Data Size: 9235639 Bytes = 8.8 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00280000
Entry Point: 0x00280000
Hash algo: sha256
Hash value: 71f2aa0d0f8353f4abf43a11a57a9b172c915cfc4ec3465716008ba17de97fa8
Verifying Hash Integrity ... sha256+ OK
## Loading ramdisk from FIT Image at 04080000 ...
Using 'conf-rockchip_boardcon-em3566.dtb' configuration
Trying 'ramdisk-1' ramdisk subimage
Description: tanowrt-image-initramfs-swu-factory
Type: RAMDisk Image
Compression: uncompressed
Data Start: 0x04968fe0
Data Size: 9330849 Bytes = 8.9 MiB
Architecture: AArch64
OS: Linux
Load Address: unavailable
Entry Point: unavailable
Hash algo: sha256
Hash value: f8102060b2d6b8d1aac88654374f422dd8a9fdcebdba200f20c0f23773b4c746
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 04080000 ...
Using 'conf-rockchip_boardcon-em3566.dtb' configuration
Trying 'fdt-rockchip_boardcon-em3566.dtb' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x0494eeec
Data Size: 106504 Bytes = 104 KiB
Architecture: AArch64
Load Address: 0x0a100000
Hash algo: sha256
Hash value: 05626803ee2cf62a4f1d782a0f4a624b3dfffa1509f9c2f7df31e5f963488bbe
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x0494eeec to 0x0a100000
Booting using the fdt blob at 0x0a100000
Uncompressing GZIP Kernel Image from 0x04080114 to 0x00280000 ... with 0157a008 bytes OK
kernel loaded at 0x00280000, end = 0x017fa008
'reserved-memory' ramoops@110000: addr=110000 size=f0000
Using Device Tree in place at 000000000a100000, end 000000000a11d007
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0x80000000 (size: 0x76c00000)
Total: 4465.564 ms
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux version 4.19.219-tano-rk-standard-g40b753b965-tano2.2.20.20.1.8 (oe-user@oe-host) (gcc version 10.3.0 (GCC), GNU ld (GNU Binutils) 2.36.1.20210703) #1 SMP Wed Jul 20 11:00:07 UTC 2022
[ 0.000000] Machine model: Boardcon EM3566 SBC Board
[ 0.000000] earlycon: uart8250 at MMIO32 0x00000000fe680000 (options '')
[ 0.000000] bootconsole [uart8250] enabled
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB
[ 0.000000] cma: Reserved 16 MiB at 0x000000007f000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 23 pages/cpu s54376 r8192 d31640 u94208
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 511496
[ 0.000000] Kernel command line: console=ttyFIQ0,1500000n8 earlycon=uart8250,mmio32,0xfe680000 root=/dev/ram rootfstype=squashfs rootwait=1 earlyprintk panic=15
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 1993212K/2078720K available (13950K kernel code, 1896K rwdata, 4656K rodata, 1472K init, 506K bss, 69124K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 50763 entries in 199 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] ITS [mem 0xfd440000-0xfd45ffff]
[ 0.000000] ITS@0x00000000fd440000: allocated 8192 Devices @7c4f0000 (indirect, esz 8, psz 64K, shr 0)
[ 0.000000] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @7c500000 (flat, esz 2, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GIC: using LPI property table @0x000000007c510000
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[ 0.000000] CPU0: using LPI pending table @0x000000007c520000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] random: random: get_random_bytes called from start_kernel+0x358/0x4e0 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.001975] Console: colour dummy device 80x25
[ 0.002436] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 0.003397] pid_max: default: 32768 minimum: 301
[ 0.004041] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.004684] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.007321] ASID allocator initialised with 32768 entries
[ 0.008001] rcu: Hierarchical SRCU implementation.
[ 0.011317] Platform MSI: interrupt-controller@fd440000 domain created
[ 0.012422] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created
[ 0.013917] smp: Bringing up secondary CPUs ...
[ 0.015182] Detected VIPT I-cache on CPU1
[ 0.015222] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[ 0.015280] CPU1: using LPI pending table @0x000000007c6b0000
[ 0.015339] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 0.016388] Detected VIPT I-cache on CPU2
[ 0.016423] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[ 0.016476] CPU2: using LPI pending table @0x000000007c700000
[ 0.016522] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ 0.017420] Detected VIPT I-cache on CPU3
[ 0.017454] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[ 0.017506] CPU3: using LPI pending table @0x000000007c720000
[ 0.017551] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ 0.017689] smp: Brought up 1 node, 4 CPUs
[ 0.024641] SMP: Total of 4 processors activated.
[ 0.025086] CPU features: detected: GIC system register CPU interface
[ 0.025687] CPU features: detected: Privileged Access Never
[ 0.026207] CPU features: detected: LSE atomic instructions
[ 0.026752] CPU features: detected: User Access Override
[ 0.027252] CPU features: detected: 32-bit EL0 Support
[ 0.027733] CPU features: detected: RAS Extension Support
[ 0.028437] CPU: All CPU(s) started at EL2
[ 0.028850] alternatives: patching kernel code
[ 0.036723] devtmpfs: initialized
[ 0.059636] Registered cp15_barrier emulation handler
[ 0.060131] Registered setend emulation handler
[ 0.060911] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.061835] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.063282] pinctrl core: initialized pinctrl subsystem
[ 0.064922] NET: Registered protocol family 16
[ 0.069392] cpuidle: using governor menu
[ 0.069803] Registered FIQ tty driver
[ 0.070610] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.073574] DMA: preallocated 2048 KiB pool for atomic allocations
[ 0.077989] console [pstore-1] enabled
[ 0.078348] pstore: Registered ramoops as persistent store backend
[ 0.078931] ramoops: attached 0xf0000@0x110000, ecc: 0/0
[ 0.110737] rockchip-gpio fdd60000.gpio: probed gpio0 (fdd60000.gpio)
[ 0.112059] rockchip-gpio fe740000.gpio: probed gpio1 (fe740000.gpio)
[ 0.113409] rockchip-gpio fe750000.gpio: probed gpio2 (fe750000.gpio)
[ 0.114687] rockchip-gpio fe760000.gpio: probed gpio3 (fe760000.gpio)
[ 0.115999] rockchip-gpio fe770000.gpio: probed gpio4 (fe770000.gpio)
[ 0.116741] rockchip-pinctrl pinctrl: probed pinctrl
[ 0.132323] cryptd: max_cpu_qlen set to 1000
[[ 0.134589] console [ttyFIQ0] enabled
0.134589] console [ttyFIQ0] enabled
[ 0.135278] bootconsole [uart8250] disabled
[ 0.135278] bootconsole [uart8250] disabled
[ 0.135973] Registered fiq debugger ttyFIQ0
[ 0.136990] vcc3v3_sys: supplied by dc_12v
[ 0.137478] vcc_1v8: supplied by vcc3v3_sys
[ 0.137970] vcc_3v3: supplied by vcc3v3_sys
[ 0.138435] vdd_fixed: supplied by vcc3v3_sys
[ 0.138933] vcc5v0_sys: supplied by dc_12v
[ 0.139442] vcc5v0_usb: supplied by dc_12v
[ 0.140089] vcc5v0_host: supplied by vcc5v0_usb
[ 0.140877] vcc5v0_otg: supplied by vcc5v0_usb
[ 0.141988] rk_iommu fde4b000.iommu: version = 2
[ 0.142673] rk_iommu fdea0800.iommu: version = 2
[ 0.143179] rk_iommu fded0480.iommu: version = 2
[ 0.143746] rk_iommu fdee0800.iommu: version = 2
[ 0.144244] rk_iommu fdef0800.iommu: version = 2
[ 0.144711] rk_iommu fdf40f00.iommu: version = 2
[ 0.145263] rk_iommu fdf80800.iommu: version = 2
[ 0.145734] rk_iommu fe043e00.iommu: version = 2
[ 0.146761] SCSI subsystem initialized
[ 0.147124] usbcore: registered new interface driver usbfs
[ 0.147226] usbcore: registered new interface driver hub
[ 0.147306] usbcore: registered new device driver usb
[ 0.147410] media: Linux media interface: v0.10
[ 0.147478] videodev: Linux video capture interface: v2.00
[ 0.147612] pps_core: LinuxPPS API ver. 1 registered
[ 0.147639] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.147683] PTP clock support registered
[ 0.148106] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ 0.150644] Advanced Linux Sound Architecture Driver Initialized.
[ 0.151360] Bluetooth: Core ver 2.22
[ 0.151433] NET: Registered protocol family 31
[ 0.151458] Bluetooth: HCI device and connection manager initialized
[ 0.151494] Bluetooth: HCI socket layer initialized
[ 0.151523] Bluetooth: L2CAP socket layer initialized
[ 0.151581] Bluetooth: SCO socket layer initialized
[ 0.152155] rockchip-cpuinfo cpuinfo: SoC : 35662000
[ 0.152188] rockchip-cpuinfo cpuinfo: Serial : ac7ac6b1f2b390e5
[ 0.153217] clocksource: Switched to clocksource arch_sys_counter
[ 0.278410] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 0.278846] NET: Registered protocol family 2
[ 0.279071] IP idents hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.280804] tcp_listen_portaddr_hash hash table entries: 1024 (order: 3, 40960 bytes)
[ 0.280892] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.281057] TCP bind hash table entries: 16384 (order: 7, 524288 bytes)
[ 0.281581] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.281789] UDP hash table entries: 1024 (order: 4, 98304 bytes)
[ 0.281929] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes)
[ 0.282298] NET: Registered protocol family 1
[ 0.283067] RPC: Registered named UNIX socket transport module.
[ 0.283095] RPC: Registered udp transport module.
[ 0.283116] RPC: Registered tcp transport module.
[ 0.283138] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.284945] Trying to unpack rootfs image as initramfs...
[ 0.948912] Freeing initrd memory: 9112K
[ 0.950391] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 0.953188] Initialise system trusted keyrings
[ 0.953598] workingset: timestamp_bits=45 max_order=19 bucket_order=0
[ 0.963818] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.964997] NFS: Registering the id_resolver key type
[ 0.965049] Key type id_resolver registered
[ 0.965064] Key type id_legacy registered
[ 0.965115] ntfs: driver 2.1.32 [Flags: R/O].
[ 0.965429] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.966014] fuse init (API version 7.27)
[ 0.966636] SGI XFS with security attributes, no debug enabled
[ 0.971270] NET: Registered protocol family 38
[ 0.971328] Key type asymmetric registered
[ 0.971345] Asymmetric key parser 'x509' registered
[ 0.971402] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 0.971430] io scheduler noop registered
[ 0.971452] io scheduler deadline registered
[ 0.971632] io scheduler cfq registered (default)
[ 0.971660] io scheduler mq-deadline registered
[ 0.971683] io scheduler kyber registered
[ 0.975117] phy phy-fe8a0000.usb2-phy.0: Linked as a consumer to regulator.8
[ 0.975511] phy phy-fe8a0000.usb2-phy.1: Linked as a consumer to regulator.9
[ 0.977247] extcon extcon1: failed to create extcon usb2-phy link
[ 0.977424] phy phy-fe8b0000.usb2-phy.2: Linked as a consumer to regulator.8
[ 0.977679] phy phy-fe8b0000.usb2-phy.3: Linked as a consumer to regulator.8
[ 0.977851] phy phy-fe8b0000.usb2-phy.3: No vbus specified for otg port
[ 0.985340] mpp_service mpp-srv: unknown mpp version for missing VCS info
[ 0.985387] mpp_service mpp-srv: probe start
[ 0.986254] iommu: Adding device fdf40000.rkvenc to group 5
[ 0.986312] mpp_rkvenc fdf40000.rkvenc: Linked as a consumer to fdf40f00.iommu
[ 0.986649] mpp_rkvenc fdf40000.rkvenc: probing start
[ 0.987327] mpp_rkvenc fdf40000.rkvenc: venc regulator not ready, retry
[ 0.987358] rkvenc_init:1199: failed to add venc devfreq
[ 0.987803] mpp_rkvenc fdf40000.rkvenc: probing finish
[ 0.989013] iommu: Adding device fdea0400.vdpu to group 1
[ 0.989069] mpp_vdpu2 fdea0400.vdpu: Linked as a consumer to fdea0800.iommu
[ 0.989303] mpp_vdpu2 fdea0400.vdpu: probe device
[ 0.990100] mpp_vdpu2 fdea0400.vdpu: probing finish
[ 0.990695] iommu: Adding device fdee0000.vepu to group 3
[ 0.990751] mpp_vepu2 fdee0000.vepu: Linked as a consumer to fdee0800.iommu
[ 0.991018] mpp_vepu2 fdee0000.vepu: probe device
[ 0.991830] mpp_vepu2 fdee0000.vepu: probing finish
[ 0.992455] iommu: Adding device fdef0000.iep to group 4
[ 0.992510] mpp-iep2 fdef0000.iep: Linked as a consumer to fdef0800.iommu
[ 0.992730] mpp-iep2 fdef0000.iep: probe device
[ 0.993436] mpp-iep2 fdef0000.iep: allocate roi buffer failed
[ 0.993698] mpp-iep2 fdef0000.iep: probing finish
[ 0.994334] iommu: Adding device fded0000.jpegd to group 2
[ 0.994388] mpp_jpgdec fded0000.jpegd: Linked as a consumer to fded0480.iommu
[ 0.994592] mpp_jpgdec fded0000.jpegd: probe device
[ 0.995375] mpp_jpgdec fded0000.jpegd: probing finish
[ 0.996035] iommu: Adding device fdf80200.rkvdec to group 6
[ 0.996097] mpp_rkvdec2 fdf80200.rkvdec: Linked as a consumer to fdf80800.iommu
[ 0.996433] mpp_rkvdec2 fdf80200.rkvdec: probing start
[ 0.996705] mpp_rkvdec2 fdf80200.rkvdec: 16 task capacity link mode detected
[ 0.997163] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_a is not found!
[ 0.997194] rkvdec2_init:661: No niu aclk reset resource define
[ 0.997215] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_h is not found!
[ 0.997230] rkvdec2_init:664: No niu hclk reset resource define
[ 0.997486] mpp_rkvdec2 fdf80200.rkvdec: sram_start 0x00000000fdcc0000
[ 0.997517] mpp_rkvdec2 fdf80200.rkvdec: rcb_iova 0x0000000010000000
[ 0.997541] mpp_rkvdec2 fdf80200.rkvdec: sram_size 45056
[ 0.997563] mpp_rkvdec2 fdf80200.rkvdec: rcb_size 65536
[ 0.997589] mpp_rkvdec2 fdf80200.rkvdec: min_width 512
[ 0.997669] mpp_rkvdec2 fdf80200.rkvdec: link mode probe finish
[ 0.997774] mpp_rkvdec2 fdf80200.rkvdec: probing finish
[ 0.998136] mpp_service mpp-srv: probe success
[ 1.006522] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330
[ 1.006598] dma-pl330 fe530000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 1.010253] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330
[ 1.010295] dma-pl330 fe550000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 1.011486] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 1.012328] vdd_logic: supplied by vcc3v3_sys
[ 1.013001] vdd_npu: supplied by vcc3v3_sys
[ 1.014090] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 1.015137] fe660000.serial: ttyS2 at MMIO 0xfe660000 (irq = 48, base_baud = 1500000) is a 16550A
[ 1.015845] fe690000.serial: ttyS5 at MMIO 0xfe690000 (irq = 49, base_baud = 1500000) is a 16550A
[ 1.018977] random: fast init done
[ 1.019164] iommu: Adding device fe040000.vop to group 7
[ 1.019230] rockchip-vop2 fe040000.vop: Linked as a consumer to fe043e00.iommu
[ 1.019329] random: crng init done
[ 1.024080] rockchip-drm display-subsystem: Linked as a consumer to fe040000.vop
[ 1.025367] rockchip-drm display-subsystem: Linked as a consumer to fe0a0000.hdmi
[ 1.027382] rockchip-drm display-subsystem: defer getting devfreq
[ 1.027755] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x0, primary plane phy id: -1
[ 1.027795] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x0, primary plane phy id: -1
[ 1.027830] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[ 1.028228] [drm] unsupported AFBC format[3432564e]
[ 1.028317] [drm] failed to init overlay plane Cluster0-win1
[ 1.028412] [drm] failed to init overlay plane Cluster1-win1
[ 1.028728] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffff8008ef9158)
[ 1.029041] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 1.029857] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[ 1.030796] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffff8008efd220)
[ 1.030833] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 1.030856] [drm] No driver support for vblank timestamp query.
[ 1.031051] rockchip-drm display-subsystem: failed to parse loader memory
[ 1.031132] [drm] Cannot find any crtc or sizes
[ 1.031326] [drm] Cannot find any crtc or sizes
[ 1.032523] [drm] Initialized rockchip 2.0.0 20140818 for display-subsystem on minor 0
[ 1.040203] mali fde60000.gpu: Kernel DDK version g7p1-01bet0
[ 1.040446] mali fde60000.gpu: Linked as a consumer to regulator.5
[ 1.040648] mali fde60000.gpu: dev_pm_opp_set_regulators: no regulator (shadercores) found: -19
[ 1.040802] mali fde60000.gpu: leakage=5
[ 1.041480] mali fde60000.gpu: avs=0
[ 1.041524] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 112; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[ 1.041632] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 1.042018] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0
[ 1.042186] mali fde60000.gpu: No priority control manager is configured
[ 1.042224] mali fde60000.gpu: No memory group manager is configured
[ 1.042875] brd: module loaded
[ 1.043032] mali fde60000.gpu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[ 1.044289] mali fde60000.gpu: Probed as mali0
[ 1.052841] loop: module loaded
[ 1.053560] zram: Added device: zram0
[ 1.053748] lkdtm: No crash points registered, enable through debugfs
[ 1.057246] libphy: Fixed MDIO Bus: probed
[ 1.058872] rk_gmac-dwmac fe010000.ethernet: no regulator found
[ 1.058914] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output).
[ 1.058933] rk_gmac-dwmac fe010000.ethernet: TX delay(0x4f).
[ 1.058949] rk_gmac-dwmac fe010000.ethernet: RX delay(0x25).
[ 1.058972] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[ 1.064072] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[ 1.064403] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 1.064434] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5
[ 1.064461] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
[ 1.064485] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
[ 1.064508] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[ 1.064529] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[ 1.064591] rk_gmac-dwmac fe010000.ethernet: TSO supported
[ 1.064608] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.064626] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[ 1.196592] libphy: stmmac: probed
[ 1.204567] PPP generic driver version 2.4.2
[ 1.204896] PPP MPPE Compression module registered
[ 1.204927] NET: Registered protocol family 24
[ 1.205284] usbcore: registered new interface driver cdc_ether
[ 1.217747] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.217802] ehci-pci: EHCI PCI platform driver
[ 1.217906] ehci-platform: EHCI generic platform driver
[ 1.219927] ehci-platform fd800000.usb: EHCI Host Controller
[ 1.220233] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[ 1.220406] devfreq fde60000.gpu: Couldn't update frequency transition information.
[ 1.221071] ehci-platform fd800000.usb: irq 11, io mem 0xfd800000
[ 1.233252] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[ 1.233603] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 1.233636] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.233661] usb usb1: Product: EHCI Host Controller
[ 1.233684] usb usb1: Manufacturer: Linux 4.19.219-tano-rk-standard-g40b753b965-tano2.2.20.20.1.8 ehci_hcd
[ 1.233705] usb usb1: SerialNumber: fd800000.usb
[ 1.234396] hub 1-0:1.0: USB hub found
[ 1.234472] hub 1-0:1.0: 1 port detected
[ 1.237323] ehci-platform fd880000.usb: EHCI Host Controller
[ 1.237604] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2
[ 1.238306] ehci-platform fd880000.usb: irq 13, io mem 0xfd880000
[ 1.249915] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[ 1.250507] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 1.250541] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.250567] usb usb2: Product: EHCI Host Controller
[ 1.250591] usb usb2: Manufacturer: Linux 4.19.219-tano-rk-standard-g40b753b965-tano2.2.20.20.1.8 ehci_hcd
[ 1.250613] usb usb2: SerialNumber: fd880000.usb
[ 1.251350] hub 2-0:1.0: USB hub found
[ 1.251468] hub 2-0:1.0: 1 port detected
[ 1.252579] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.252628] ohci-platform: OHCI generic platform driver
[ 1.252974] ohci-platform fd840000.usb: Generic Platform OHCI controller
[ 1.253314] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3
[ 1.253927] ohci-platform fd840000.usb: irq 12, io mem 0xfd840000
[ 1.314187] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 1.314219] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.314236] usb usb3: Product: Generic Platform OHCI controller
[ 1.314252] usb usb3: Manufacturer: Linux 4.19.219-tano-rk-standard-g40b753b965-tano2.2.20.20.1.8 ohci_hcd
[ 1.314266] usb usb3: SerialNumber: fd840000.usb
[ 1.314938] hub 3-0:1.0: USB hub found
[ 1.315017] hub 3-0:1.0: 1 port detected
[ 1.315776] ohci-platform fd8c0000.usb: Generic Platform OHCI controller
[ 1.316038] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[ 1.316459] ohci-platform fd8c0000.usb: irq 14, io mem 0xfd8c0000
[ 1.374204] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 1.374237] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.374254] usb usb4: Product: Generic Platform OHCI controller
[ 1.374268] usb usb4: Manufacturer: Linux 4.19.219-tano-rk-standard-g40b753b965-tano2.2.20.20.1.8 ohci_hcd
[ 1.374282] usb usb4: SerialNumber: fd8c0000.usb
[ 1.374981] hub 4-0:1.0: USB hub found
[ 1.375058] hub 4-0:1.0: 1 port detected
[ 1.377049] usbcore: registered new interface driver cdc_acm
[ 1.377081] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.377443] usbcore: registered new interface driver uas
[ 1.377632] usbcore: registered new interface driver usb-storage
[ 1.377786] usbcore: registered new interface driver usbserial_generic
[ 1.377848] usbserial: USB Serial support registered for generic
[ 1.377934] usbcore: registered new interface driver ftdi_sio
[ 1.377991] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 1.378255] usbcore: registered new interface driver keyspan
[ 1.378310] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 1.378363] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 1.378423] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 1.378484] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 1.378573] usbcore: registered new interface driver oti6858
[ 1.378629] usbserial: USB Serial support registered for oti6858
[ 1.378700] usbcore: registered new interface driver qcserial
[ 1.378757] usbserial: USB Serial support registered for Qualcomm USB modem
[ 1.381308] i2c /dev entries driver
[ 1.499932] usb 2-1: new high-speed USB device number 2 using ehci-platform
[ 1.648375] usb 2-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.36
[ 1.648409] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.648426] usb 2-1: Product: USB2.0 Hub
[ 1.649300] hub 2-1:1.0: USB hub found
[ 1.649757] hub 2-1:1.0: 4 ports detected
[ 2.383259] rk3x-i2c fdd40000.i2c: timeout, ipd: 0x00, state: 1
[ 2.383303] fan53555-regulator 0-001c: Failed to get chip ID!
[ 2.383417] fan53555-regulator: probe of 0-001c failed with error -110
[ 3.396592] rk3x-i2c fe5a0000.i2c: timeout, ipd: 0x00, state: 2
[ 3.396637] rtc-hym8563 1-0051: could not init device, -110
[ 3.396707] rtc-hym8563: probe of 1-0051 failed with error -110
[ 3.400010] usbcore: registered new interface driver uvcvideo
[ 3.400041] USB Video Class driver (1.1.1)
[ 3.400325] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.4
[ 3.400363] rockchip-iodomain fdc20000.syscon:io-domains: pmuio1(3300000 uV) supplied by vcc_3v3
[ 3.400525] rockchip-iodomain fdc20000.syscon:io-domains: pmuio2(3300000 uV) supplied by vcc_3v3
[ 3.400662] rockchip-iodomain fdc20000.syscon:io-domains: vccio1(3300000 uV) supplied by vcc_3v3
[ 3.400786] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.3
[ 3.400830] rockchip-iodomain fdc20000.syscon:io-domains: vccio2(1800000 uV) supplied by vcc_1v8
[ 3.400973] rockchip-iodomain fdc20000.syscon:io-domains: vccio3(3300000 uV) supplied by vcc_3v3
[ 3.401117] rockchip-iodomain fdc20000.syscon:io-domains: vccio4(1800000 uV) supplied by vcc_1v8
[ 3.401251] rockchip-iodomain fdc20000.syscon:io-domains: vccio5(3300000 uV) supplied by vcc_3v3
[ 3.401405] rockchip-iodomain fdc20000.syscon:io-domains: vccio6(1800000 uV) supplied by vcc_1v8
[ 3.401539] rockchip-iodomain fdc20000.syscon:io-domains: vccio7(3300000 uV) supplied by vcc_3v3
[ 3.404820] rockchip-thermal fe710000.tsadc: tsadc is probed successfully!
[ 3.406242] usbcore: registered new interface driver bfusb
[ 3.406359] usbcore: registered new interface driver btusb
[ 3.406772] cpu cpu0: leakage=18
[ 3.406887] cpu cpu0: Failed to get reg
[ 3.408557] sdhci: Secure Digital Host Controller Interface driver
[ 3.408586] sdhci: Copyright(c) Pierre Ossman
[ 3.408609] Synopsys Designware Multimedia Card Interface Driver
[ 3.409911] dwmmc_rockchip fe2b0000.dwmmc: IDMAC supports 32-bit address mode.
[ 3.410350] dwmmc_rockchip fe2b0000.dwmmc: Using internal DMA controller.
[ 3.410388] dwmmc_rockchip fe2b0000.dwmmc: Version ID is 270a
[ 3.410476] dwmmc_rockchip fe2b0000.dwmmc: DW MMC controller at irq 38,32 bit host data width,256 deep fifo
[ 3.410629] dwmmc_rockchip fe2b0000.dwmmc: Linked as a consumer to regulator.4
[ 3.424179] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 3.437688] dwmmc_rockchip fe2c0000.dwmmc: IDMAC supports 32-bit address mode.
[ 3.438506] dwmmc_rockchip fe2c0000.dwmmc: Using internal DMA controller.
[ 3.438557] dwmmc_rockchip fe2c0000.dwmmc: Version ID is 270a
[ 3.438656] dwmmc_rockchip fe2c0000.dwmmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo
[ 3.438866] mmc_host mmc2: card is non-removable.
[ 3.452229] mmc_host mmc2: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 3.465273] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.467344] mmc0: Unknown controller version (5). You may experience problems.
[ 3.471307] mmc1: Problem switching card into high-speed mode!
[ 3.471416] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot req 25000000Hz, actual 25000000HZ div = 0)
[ 3.471732] mmc1: new SDHC card at address 0001
[ 3.473361] mmcblk1: mmc1:0001 00000 14.6 GiB
[ 3.475872] mmc2 mmc_send_io_op_cond err: -110
[ 3.484303] mmcblk1: p1 p2 p3
[ 3.489836] mmc_host mmc2: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0)
[ 3.499224] mmc0: SDHCI controller on fe310000.sdhci [fe310000.sdhci] using ADMA
[ 3.500844] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.501451] usbcore: registered new interface driver usbhid
[ 3.501480] usbhid: USB HID core driver
[ 3.502051] rockchip,bus bus-npu: Linked as a consumer to regulator.10
[ 3.502097] rockchip,bus bus-npu: Failed to get leakage
[ 3.502218] rockchip,bus bus-npu: Failed to get reg
[ 3.502691] rockchip,bus bus-npu: avs=0
[ 3.505138] rockchip-saradc fe720000.saradc: Linked as a consumer to regulator.3
[ 3.506204] optee: probing for conduit method from DT.
[ 3.506255] optee: revision 3.6 (0b06ae94)
[ 3.506893] optee: initialized driver
[ 3.506930] rksfc_base v1.1 2016-01-08
[ 3.507800] rksfc fe300000.sfc: rksfc_probe clk rate = 99000000
[ 3.507917] rkflash_dev_init enter
[ 3.507956] sfc nor id: 0 0 0
[ 3.507979] rkflash[1] is invalid
[ 3.507983] rkflash_dev_init enter
[ 3.508011] sfc_nand id: 0 0 0
[ 3.508022] rkflash[2] is invalid
[ 3.509045] usbcore: registered new interface driver snd-usb-audio
[ 3.514243] mmc2 mmc_send_io_op_cond err: -110
[ 3.516751] NET: Registered protocol family 26
[ 3.516794] u32 classifier
[ 3.516806] Actions configured
[ 3.516960] Initializing XFRM netlink socket
[ 3.517689] NET: Registered protocol family 10
[ 3.518930] Segment Routing with IPv6
[ 3.519041] NET: Registered protocol family 17
[ 3.519079] NET: Registered protocol family 15
[ 3.519183] Bridge firewalling registered
[ 3.519446] Bluetooth: RFCOMM socket layer initialized
[ 3.519506] Bluetooth: RFCOMM ver 1.11
[ 3.519533] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.519554] Bluetooth: HIDP socket layer initialized
[ 3.519646] l2tp_core: L2TP core driver, V2.0
[ 3.519682] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 3.519705] l2tp_netlink: L2TP netlink interface
[ 3.519770] 8021q: 802.1Q VLAN Support v1.8
[ 3.519819] [BT_RFKILL]: Enter rfkill_rk_init
[ 3.519841] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 3.520754] Key type dns_resolver registered
[ 3.521335] flash vendor_init_thread!
[ 3.521356] flash vendor storage:20170308 ret = -1
[ 3.522891] Loading compiled-in X.509 certificates
[ 3.523819] pstore: Using compression: deflate
[ 3.525280] rga2: Driver loaded successfully ver:3.2.63318
[ 3.525742] rga2: Module initialized.
[ 3.536613] mmc0: new HS200 MMC card at address 0001
[ 3.538041] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB
[ 3.538844] mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB
[ 3.539635] mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB
[ 3.540098] mmcblk0rpmb: mmc0:0001 8GTF4R partition 3 512 KiB, chardev (238:0)
[ 3.544204] mmcblk0: p1 p2 p3 p4 p5 p6
[ 3.550562] mmc2 mmc_send_io_op_cond err: -110
[ 3.575767] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 3.587311] mmc2 mmc_send_io_op_cond err: -110
[ 3.588182] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 3.590386] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 413; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '11:00:58', on 'Jul 20 2022'.
[ 3.590944] Mali:
[ 3.590947] Mali device driver loaded
[ 3.591137] ALSA device list:
[ 3.591161] No soundcards found.
[ 3.594657] Freeing unused kernel memory: 1472K
[ 3.595146] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 3.595180] cfg80211: failed to load regulatory.db
[ 3.606774] Run /init as init process
[ 3.650502] vendor storage:20190527 ret = 0
[ 4.025812] init: Console is alive
[ 4.026131] init: - watchdog -
[ 4.029542] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.029707] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.037002] init: - preinit -
Press the [x] key to cancel automatic installation
Press the [r] key to install without last action (reboot/power off)
┌────────────────────────┐
│ │
│ Global configuration │
│ │
└────────────────────────┘
* Last action: reboot
* Last action delay: 5 seconds
┌────────────────┐
│ │
│ Verification │
│ │
└────────────────┘
Checking required block devices...
════════════════════════════════════════════════════════════════════════════════
Block device /dev/mmcblk0 found
Block device /dev/mmcblk1 found
┌────────────────────┐
│ │
│ Pre-installation │
│ │
└────────────────────┘
Mounting filesystems...
════════════════════════════════════════════════════════════════════════════════
Mount 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk1p3
* Target: /mnt
* Filsystem: vfat
* Create target: yes
Executing command '/bin/mount -t vfat /dev/mmcblk1p3 /mnt'...
Executed '/bin/mount -t vfat /dev/mmcblk1p3 /mnt' with exit code 0
Mounted
Erasing block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0
* Block size: 512
* Count: 131072
Executing command '/bin/dd if=/dev/zero of=/dev/mmcblk0 bs=512 count=131072'...
131072+0 records in
131072+0 records out
Executed '/bin/dd if=/dev/zero of=/dev/mmcblk0 bs=512 count=131072' with exit code 0
Block device /dev/mmcblk0 erased
Creating partitions on block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0
* Label: gpt
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mklabel gpt'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mklabel gpt' with exit code 0
Executing command '/usr/sbin/partprobe'...
Executed '/usr/sbin/partprobe' with exit code 0
Partition 1:
* Name: boot
* Partition type: primary
* Start: 8MiB
* End: 16MiB
* UUID: dc8f9328-92f5-497e-a845-6f564ef32034
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 8MiB 16MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 8MiB 16MiB' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 1 'boot''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 1 'boot'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=1:dc8f9328-92f5-497e-a845-6f564ef32034 /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=1:dc8f9328-92f5-497e-a845-6f564ef32034 /dev/mmcblk0' with exit code 0
Partition 2:
* Name: kernel_a
* Partition type: primary
* Filesystem type: ext4
* Start: 16MiB
* End: 80MiB
* UUID: a0a965a8-8328-4540-8543-786c9e88b7b8
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 16MiB 80MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 16MiB 80MiB' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 2 'kernel_a''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 2 'kernel_a'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=2:a0a965a8-8328-4540-8543-786c9e88b7b8 /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=2:a0a965a8-8328-4540-8543-786c9e88b7b8 /dev/mmcblk0' with exit code 0
Partition 3:
* Name: rootfs_a
* Partition type: primary
* Start: 80MiB
* End: 1104MiB
* UUID: d3aa42ba-48e8-4d08-9676-f630d3746140
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 80MiB 1104MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 80MiB 1104MiB' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 3 'rootfs_a''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 3 'rootfs_a'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=3:d3aa42ba-48e8-4d08-9676-f630d3746140 /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=3:d3aa42ba-48e8-4d08-9676-f630d3746140 /dev/mmcblk0' with exit code 0
Partition 4:
* Name: kernel_b
* Partition type: primary
* Filesystem type: ext4
* Start: 1104MiB
* End: 1168MiB
* UUID: ec341c88-9b34-4027-9e7e-33c5900c95f6
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 1104MiB 1168MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 1104MiB 1168MiB' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 4 'kernel_b''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 4 'kernel_b'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=4:ec341c88-9b34-4027-9e7e-33c5900c95f6 /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=4:ec341c88-9b34-4027-9e7e-33c5900c95f6 /dev/mmcblk0' with exit code 0
Partition 5:
* Name: rootfs_b
* Partition type: primary
* Start: 1168MiB
* End: 2192MiB
* UUID: ec087a31-9005-49df-b77b-d7c4312a0511
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 1168MiB 2192MiB'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary 1168MiB 2192MiB' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 5 'rootfs_b''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 5 'rootfs_b'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=5:ec087a31-9005-49df-b77b-d7c4312a0511 /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=5:ec087a31-9005-49df-b77b-d7c4312a0511 /dev/mmcblk0' with exit code 0
Partition 6:
* Name: rootfs_data
* Partition type: primary
* Filesystem type: ext4
* Start: 2192MiB
* End: 100%
* UUID: 8b06d263-67ab-452e-a126-cc8345d60f9c
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 2192MiB 100%'...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script mkpart primary ext4 2192MiB 100%' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script name 6 'rootfs_data''...
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script name 6 'rootfs_data'' with exit code 0
Executing command '/usr/sbin/sgdisk --partition-guid=6:8b06d263-67ab-452e-a126-cc8345d60f9c /dev/mmcblk0'...
The operation has completed successfully.
Executed '/usr/sbin/sgdisk --partition-guid=6:8b06d263-67ab-452e-a126-cc8345d60f9c /dev/mmcblk0' with exit code 0
Executing command '/usr/sbin/parted -s /dev/mmcblk0 --script print'...
Model: MMC 8GTF4R (sd/mmc)
Disk /dev/mmcblk0: 7818MB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:
Number Start End Size File system Name Flags
1 8389kB 16.8MB 8389kB boot
2 16.8MB 83.9MB 67.1MB kernel_a
3 83.9MB 1158MB 1074MB rootfs_a
4 1158MB 1225MB 67.1MB ext4 kernel_b
5 1225MB 2298MB 1074MB rootfs_b
6 2298MB 7817MB 5519MB ext4 rootfs_data
Executed '/usr/sbin/parted -s /dev/mmcblk0 --script print' with exit code 0
Executing command '/usr/sbin/partprobe'...
Executed '/usr/sbin/partprobe' with exit code 0
Created partitions on block device /dev/mmcblk0
Creating filesystems on block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0p6
* Filesystem type: ext4
* Label: rootfs_data
Executing command '/sbin/mkfs.ext4 -F -L rootfs_data /dev/mmcblk0p6'...
mke2fs 1.46.1 (9-Feb-2021)
/dev/mmcblk0p6 contains a ext4 file system labelled 'rootfs_data'
created on Thu Jan 1 00:00:21 1970
Discarding device blocks: done
Creating filesystem with 1347328 4k blocks and 337344 inodes
Filesystem UUID: 7fc16c84-0176-4943-a3d0-f1c351ba16ed
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736
Allocating group tables: done
Writing inode tables: done
Creating journal (16384 blocks): done
Writing superblocks and filesystem accounting information: done
Executed '/sbin/mkfs.ext4 -F -L rootfs_data /dev/mmcblk0p6' with exit code 0
Created ext4 filesystem on /dev/mmcblk0p6
Writing images to block devices...
════════════════════════════════════════════════════════════════════════════════
Block device 1
────────────────────────────────────────────────────────────
* Device: /dev/mmcblk0
Image 1:
* Image source: local
* Image URL: /mnt/u-boot-initial-env.bin
* Offset: 4128768 bytes
Executing command '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=4128768 seek=1'...
0+1 records in
0+1 records out
Executed '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=4128768 seek=1' with exit code 0
Image 2:
* Image source: local
* Image URL: /mnt/u-boot-initial-env.bin
* Offset: 4161536 bytes
Executing command '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=4161536 seek=1'...
0+1 records in
0+1 records out
Executed '/bin/dd if=/mnt/u-boot-initial-env.bin of=/dev/mmcblk0 bs=4161536 seek=1' with exit code 0
Writed images to block device /dev/mmcblk0
┌────────────────┐
│ │
│ Installation │
│ │
└────────────────┘
┌─────────────────────┐
│ │
│ Installing images │
│ │
└─────────────────────┘
Installing image 1...
════════════════════════════════════════════════════════════════════════════════
* Type: swupdate
* Image source: local
* Image URL: /mnt/swu_install.swu
* Extra arguments: --no-bootloader-env
* Dry run: 1
* Install: 1
* Selections: ${SWU_SYSTEM_A_SELECTION} ${SWU_SYSTEM_B_SELECTION}
* Selections (expanded): tanowrt,system-a tanowrt,system-b
[dry] run for selection 'tanowrt,system-a'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.6.rk0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on boardcon-em3566-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-a
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 4035
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2022-07-20-11:45:05-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for Boardcon EM3566 SBC (eMMC) (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_a 2022-07-20-11:45:05-UTC: tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo in device : /dev/mmcblk0p3 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_a 4.19.219+gitAUTOINC+40b753b965-tano2.2.20.20.1.8: fitImage-boardcon-em3566-emmc.ext4 in device : /dev/mmcblk0p2 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.rk0: startup-boardcon-em3566-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2017.09-gitAUTOINC+e3ca3c3805_fe66a9be19-tano8: u-boot-boardcon-em3566-emmc.bin-emmc in device : /dev/mmcblk0p1 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image idblock d0d58d6f04fd4bf89750887aa292c5f9: idblock.img-boardcon-em3566-emmc-emmc in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 0
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware boardcon-em3566-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 47874048
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo, 47874048 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename idblock.img-boardcon-em3566-emmc-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 296960
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-boardcon-em3566-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 2097152
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-boardcon-em3566-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2168
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-boardcon-em3566-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 12255232
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-boardcon-em3566-emmc.ext4, 12255232 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-boardcon-em3566-emmc.ext4 dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream idblock.img-boardcon-em3566-emmc-emmc dummy
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 32768 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-boardcon-em3566-emmc.bin-emmc dummy
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-boardcon-em3566-emmc.img dummy
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 4063232 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-a' [dry] run success
[dry] run for selection 'tanowrt,system-b'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.6.rk0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on boardcon-em3566-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-b
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 4035
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2022-07-20-11:45:05-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for Boardcon EM3566 SBC (eMMC) (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_b 2022-07-20-11:45:05-UTC: tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo in device : /dev/mmcblk0p5 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_b 4.19.219+gitAUTOINC+40b753b965-tano2.2.20.20.1.8: fitImage-boardcon-em3566-emmc.ext4 in device : /dev/mmcblk0p4 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.rk0: startup-boardcon-em3566-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2017.09-gitAUTOINC+e3ca3c3805_fe66a9be19-tano8: u-boot-boardcon-em3566-emmc.bin-emmc in device : /dev/mmcblk0p1 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image idblock d0d58d6f04fd4bf89750887aa292c5f9: idblock.img-boardcon-em3566-emmc-emmc in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 1
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware boardcon-em3566-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 47874048
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo, 47874048 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename idblock.img-boardcon-em3566-emmc-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 296960
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-boardcon-em3566-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 2097152
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-boardcon-em3566-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2168
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-boardcon-em3566-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 12255232
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-boardcon-em3566-emmc.ext4, 12255232 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-boardcon-em3566-emmc.ext4 dummy
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream idblock.img-boardcon-em3566-emmc-emmc dummy
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 32768 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-boardcon-em3566-emmc.bin-emmc dummy
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-boardcon-em3566-emmc.img dummy
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 4063232 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu -n --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-b' [dry] run success
[install] run for selection 'tanowrt,system-a'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.6.rk0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on boardcon-em3566-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-a
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 4035
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2022-07-20-11:45:05-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for Boardcon EM3566 SBC (eMMC) (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_a 2022-07-20-11:45:05-UTC: tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo in device : /dev/mmcblk0p3 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_a 4.19.219+gitAUTOINC+40b753b965-tano2.2.20.20.1.8: fitImage-boardcon-em3566-emmc.ext4 in device : /dev/mmcblk0p2 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.rk0: startup-boardcon-em3566-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2017.09-gitAUTOINC+e3ca3c3805_fe66a9be19-tano8: u-boot-boardcon-em3566-emmc.bin-emmc in device : /dev/mmcblk0p1 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image idblock d0d58d6f04fd4bf89750887aa292c5f9: idblock.img-boardcon-em3566-emmc-emmc in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 0
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware boardcon-em3566-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh preupdate tanowrt system-a command returned 0
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 47874048
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo, 47874048 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename idblock.img-boardcon-em3566-emmc-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 296960
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-boardcon-em3566-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 2097152
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-boardcon-em3566-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2168
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-boardcon-em3566-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 12255232
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-boardcon-em3566-emmc.ext4, 12255232 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-boardcon-em3566-emmc.ext4 raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream idblock.img-boardcon-em3566-emmc-emmc raw
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 32768 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-boardcon-em3566-emmc.bin-emmc raw
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-boardcon-em3566-emmc.img raw
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 4063232 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh postupdate-success tanowrt system-a command returned 0
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-a -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-a' [install] run success
[install] run for selection 'tanowrt,system-b'
────────────────────────────────────────────────────────────
Executing command 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env'...
[TRACE] : SWUPDATE running : [main] : transaction_marker globally disabled
[TRACE] : SWUPDATE running : [main] : bootloader environment changes globally disabled
Swupdate v2021.04.0-git49e958fe46c2-r0.tano0.6.rk0
Licensed under GPLv2. See source distribution for detailed copyright notices.
[INFO ] : SWUPDATE running : [main] : Running on boardcon-em3566-emmc Revision 1.0
[INFO ] : SWUPDATE running : [print_registered_handlers] : Registered handlers:
[INFO ] : SWUPDATE running : [print_registered_handlers] : dummy
[INFO ] : SWUPDATE running : [print_registered_handlers] : archive
[INFO ] : SWUPDATE running : [print_registered_handlers] : tar
[INFO ] : SWUPDATE running : [print_registered_handlers] : uboot
[INFO ] : SWUPDATE running : [print_registered_handlers] : bootloader
[INFO ] : SWUPDATE running : [print_registered_handlers] : lua
[INFO ] : SWUPDATE running : [print_registered_handlers] : raw
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawfile
[INFO ] : SWUPDATE running : [print_registered_handlers] : rawcopy
[INFO ] : SWUPDATE running : [print_registered_handlers] : shellscript
[INFO ] : SWUPDATE running : [print_registered_handlers] : preinstall
[INFO ] : SWUPDATE running : [print_registered_handlers] : postinstall
[INFO ] : SWUPDATE running : [main] : software set: tanowrt mode: system-b
[TRACE] : SWUPDATE running : [network_initializer] : Main loop daemon
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/swupdateprog
[TRACE] : SWUPDATE running : [listener_create] : creating socket at /tmp/sockinstctrl
[TRACE] : SWUPDATE running : [network_thread] : Incoming network request: processing...
[INFO ] : SWUPDATE started : Software Update started !
[TRACE] : SWUPDATE running : [network_initializer] : Software update started
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : Found file
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : filename sw-description
[TRACE] : SWUPDATE running : [extract_file_to_tmp] : size 4035
[TRACE] : SWUPDATE running : [get_common_fields] : Version 2022-07-20-11:45:05-UTC
[TRACE] : SWUPDATE running : [get_common_fields] : Description Firmware upgrade for Boardcon EM3566 SBC (eMMC) (eMMC)
[TRACE] : SWUPDATE running : [parse_hw_compatibility] : Accepted Hw Revision : 1.0
[TRACE] : SWUPDATE running : [_parse_images] : Found Image rootfs_b 2022-07-20-11:45:05-UTC: tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo in device : /dev/mmcblk0p5 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [_parse_images] : Found Image kernel_b 4.19.219+gitAUTOINC+40b753b965-tano2.2.20.20.1.8: fitImage-boardcon-em3566-emmc.ext4 in device : /dev/mmcblk0p4 for handler raw (installed from stream)
[TRACE] : SWUPDATE running : [parser_follow_link] : Link found, following #./../../common/bootloader/images
[TRACE] : SWUPDATE running : [_parse_images] : Found Image startup 1.0.0-tano1.rk0: startup-boardcon-em3566-emmc.img in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image uboot 2017.09-gitAUTOINC+e3ca3c3805_fe66a9be19-tano8: u-boot-boardcon-em3566-emmc.bin-emmc in device : /dev/mmcblk0p1 for handler raw
[TRACE] : SWUPDATE running : [_parse_images] : Found Image idblock d0d58d6f04fd4bf89750887aa292c5f9: idblock.img-boardcon-em3566-emmc-emmc in device : /dev/mmcblk0 for handler raw
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_active = 1
[TRACE] : SWUPDATE running : [_parse_bootloader] : Bootloader var: swu_upgrade_available = 1
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware boardcon-em3566-emmc Revision: 1.0
[TRACE] : SWUPDATE running : [check_hw_compatibility] : Hardware compatibility verified
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh preupdate tanowrt system-b command returned 0
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo
[TRACE] : SWUPDATE running : [extract_files] : size 47874048
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo, 47874048 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream tanowrt-image-full-boardcon-em3566-emmc.squashfs-lzo raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename idblock.img-boardcon-em3566-emmc-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 296960
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename u-boot-boardcon-em3566-emmc.bin-emmc
[TRACE] : SWUPDATE running : [extract_files] : size 2097152
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename startup-boardcon-em3566-emmc.img
[TRACE] : SWUPDATE running : [extract_files] : size 2168
[TRACE] : SWUPDATE running : [extract_files] : Found file [required]
[TRACE] : SWUPDATE running : [extract_files] : filename fitImage-boardcon-em3566-emmc.ext4
[TRACE] : SWUPDATE running : [extract_files] : size 12255232
[TRACE] : SWUPDATE running : [extract_files] : Installing STREAM fitImage-boardcon-em3566-emmc.ext4, 12255232 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream fitImage-boardcon-em3566-emmc.ext4 raw
[TRACE] : SWUPDATE running : [extract_files] : END INSTALLING STREAMING
[TRACE] : SWUPDATE running : [extract_padding] : Expecting 388 padding bytes at end-of-file
[TRACE] : SWUPDATE running : [network_initializer] : Valid image found: copying to FLASH
[INFO ] : SWUPDATE running : Installation in progress
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream idblock.img-boardcon-em3566-emmc-emmc raw
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 32768 bytes
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream u-boot-boardcon-em3566-emmc.bin-emmc raw
[TRACE] : SWUPDATE running : [install_single_image] : Found installer for stream startup-boardcon-em3566-emmc.img raw
[TRACE] : SWUPDATE running : [copyfile] : offset has been defined: 4063232 bytes
[INFO ] : SWUPDATE successful ! SWUPDATE successful !
[TRACE] : SWUPDATE running : [run_system_cmd] : /usr/lib/swupdate/swupdate_hook.sh postupdate-success tanowrt system-b command returned 0
[TRACE] : SWUPDATE running : [network_initializer] : Main thread sleep again !
[INFO ] : No SWUPDATE running : Waiting for requests...
[INFO ] : SWUPDATE running : [endupdate] : Swupdate was successful !
Executed 'SWU_FACTORY_INSTALL=1 /usr/bin/swupdate -e tanowrt,system-b -v -M -f /etc/swupdate.conf -i /mnt/swu_install.swu --no-bootloader-env' with exit code 0
Selection 'tanowrt,system-b' [install] run success
┌─────────────────────┐
│ │
│ Post-installation │
│ │
└─────────────────────┘
Executing custom commands...
════════════════════════════════════════════════════════════════════════════════
Command 1
────────────────────────────────────────────────────────────
* Command: fw_setenv swu_active 0
* Required exit code : 0
Executing command 'fw_setenv swu_active 0'...
Executed 'fw_setenv swu_active 0' with exit code 0
Command 2
────────────────────────────────────────────────────────────
* Command: fw_setenv swu_upgrade_available 0
* Required exit code : 0
Executing command 'fw_setenv swu_upgrade_available 0'...
Executed 'fw_setenv swu_upgrade_available 0' with exit code 0
Command 3
────────────────────────────────────────────────────────────
* Command: fw_setenv swu_bootcount 0
* Required exit code : 0
Executing command 'fw_setenv swu_bootcount 0'...
Executed 'fw_setenv swu_bootcount 0' with exit code 0
┌────────────────────────────────────────────────┐
│ │
│ SUCCESS: Installation successfully completed │
│ │
└────────────────────────────────────────────────┘
Rebooting in 5 seconds...
Rebooting in 4 seconds...
Rebooting in 3 seconds...
Rebooting in 2 seconds...
Rebooting in 1 seconds...
Rebooting now...
[ 42.538909] reboot: Restarting system