2.12.2 SAMA5D3 Xplained Boot from internal NAND Log
TanoWrt boot log from internal NAND flash.
RomBOOT
AT91Bootstrap 3.10.1-rc1-gitAUTOINC+1d013b417b-r0.tano1 (2022-08-07 22:54:56)
NAND: ONFI flash detected
NAND: Manufacturer ID: 0x2c Chip ID: 0xda
NAND: Page Bytes: 2048, Spare Bytes: 64
NAND: ECC Correctability Bits: 4, ECC Sector Bytes: 512
NAND: Disable On-Die ECC
NAND: Initialize PMECC params, cap: 4, sector: 512
NAND: Image: Copy 0xc0000 bytes from 0x40000 to 0x26f00000
NAND: Done to load image
<debug_uart>
U-Boot 2020.01-gitAUTOINC+af59b26c22-tano0.2 (Aug 09 2022 - 23:38:03 +0000)
CPU: SAMA5D36
Crystal frequency: 12 MHz
CPU clock : 528 MHz
Master clock : 132 MHz
DRAM: 256 MiB
NAND: 256 MiB
MMC: Atmel mci: 0, Atmel mci: 1
Loading Environment from NAND... OK
In: serial@ffffee00
Out: serial@ffffee00
Err: serial@ffffee00
Net:
Warning: ethernet@f0028000 MAC addresses don't match:
Address in ROM is 00:10:a1:98:97:02
Address in environment is 00:10:a1:98:97:01
eth0: ethernet@f0028000, eth1: ethernet@f802c000
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x180000, size 0x40000
262144 bytes read: OK
## Executing script at 21000000
Board name:
Active system A
Loading kernel fitImage...
ubi0: attaching mtd5
ubi0: scanning is finished
ubi0: attached mtd5 (name "system_a", size 104 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 832, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1316010412
ubi0: available PEBs: 562, total reserved PEBs: 270, PEBs reserved for bad PEB handling: 40
No size specified -> Using max size (4698112)
Read 4698112 bytes from volume kernel to 24000000
Booting kernel 0x24000000#conf-at91-sama5d3_xplained.dtb...
## Loading kernel from FIT Image at 24000000 ...
Using 'conf-at91-sama5d3_xplained.dtb' configuration
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x24000118
Data Size: 4567560 Bytes = 4.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x22000000
Entry Point: 0x22000000
Hash algo: sha256
Hash value: ee89b790ef96b8d52a38f4d389c2147d6f9e7f9703a497a3001810c8e0ebea70
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 24000000 ...
Using 'conf-at91-sama5d3_xplained.dtb' configuration
Trying 'fdt-at91-sama5d3_xplained.dtb' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x2445b438
Data Size: 49941 Bytes = 48.8 KiB
Architecture: ARM
Load Address: 0x23e00000
Hash algo: sha256
Hash value: e3f2fc684562136c01081975e579280f1c9d0fa41d579ebb57add47dad0f1f3f
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x2445b438 to 0x23e00000
Booting using the fdt blob at 0x23e00000
Loading Kernel Image
Loading Device Tree to 2fb1e000, end 2fb2d314 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.78-tano-at91-standard-g046113c438-tano0.2.20.20.0.0 (oe-user@oe-host) (gcc version 10.3.0 (GCC)) #1 Tue Aug 9 23:24:05 UTC 2022
[ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: SAMA5D3 Xplained
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x2e800000
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] random: get_random_bytes called from 0xc0a008e8 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 ubi.mtd=system_a,2048 ubi.mtd=rootfs_data,2048 ubi.block=0,rootfs root=/dev/ubiblock0_1 ro rootfstype=squashfs rootwait rootfs_partition=system_a rootfs_volume=rootfs earlyprintk panic=15
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 232316K/262144K available (7168K kernel code, 272K rwdata, 1296K rodata, 1024K init, 169K bss, 13444K reserved, 16384K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (8160 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 273 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 170 kB)
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: timer@f0010000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 115833966437 ns
[ 0.000019] sched_clock: 32 bits at 16MHz, resolution 60ns, wraps every 130150523873ns
[ 0.000045] Switching to timer-based delay loop, resolution 60ns
[ 0.000634] clocksource: pit: mask: 0xfffffff max_cycles: 0xfffffff, max_idle_ns: 14479245754 ns
[ 0.001235] Console: colour dummy device 80x30
[ 0.001310] Calibrating delay loop (skipped), value calculated using timer frequency.. 33.00 BogoMIPS (lpj=165000)
[ 0.001343] pid_max: default: 32768 minimum: 301
[ 0.001662] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001699] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.003070] CPU: Testing write buffer coherency: ok
[ 0.004512] Setting up static identity map for 0x20100000 - 0x20100060
[ 0.006408] devtmpfs: initialized
[ 0.024658] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 0.025069] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.025109] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.027107] pinctrl core: initialized pinctrl subsystem
[ 0.029070] NET: Registered protocol family 16
[ 0.031630] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.034016] cpuidle: using governor menu
[ 0.057034] AT91: PM: standby: standby, suspend: ulp0
[ 0.058324] gpio-at91 fffff200.gpio: at address (ptrval)
[ 0.059525] gpio-at91 fffff400.gpio: at address (ptrval)
[ 0.060911] gpio-at91 fffff600.gpio: at address (ptrval)
[ 0.062292] gpio-at91 fffff800.gpio: at address (ptrval)
[ 0.063766] gpio-at91 fffffa00.gpio: at address (ptrval)
[ 0.065609] pinctrl-at91 ahb:apb:pinctrl@fffff200: initialized AT91 pinctrl driver
[ 0.066364] atmel_tcb: probe of f0010000.timer failed with error -16
[ 0.082954] at_hdmac ffffe600.dma-controller: Atmel AHB DMA Controller ( cpy set slave ), 8 channels
[ 0.084751] at_hdmac ffffe800.dma-controller: Atmel AHB DMA Controller ( cpy set slave ), 8 channels
[ 0.087350] AT91: Detected SoC family: sama5d3
[ 0.087376] AT91: Detected SoC: sama5d36, revision 2
[ 0.089057] SCSI subsystem initialized
[ 0.089631] usbcore: registered new interface driver usbfs
[ 0.089763] usbcore: registered new interface driver hub
[ 0.089910] usbcore: registered new device driver usb
[ 0.091615] at91_i2c f0014000.i2c: using dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers
[ 0.092049] at91_i2c f0014000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.093363] at91_i2c f0018000.i2c: using dma0chan2 (tx) and dma0chan3 (rx) for DMA transfers
[ 0.093773] at91_i2c f0018000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.094425] at91_i2c f801c000.i2c: can't get DMA channel, continue without DMA support
[ 0.094777] at91_i2c f801c000.i2c: AT91 i2c bus driver (hw version: 0x402).
[ 0.095591] media: Linux media interface: v0.10
[ 0.095699] videodev: Linux video capture interface: v2.00
[ 0.095801] pps_core: LinuxPPS API ver. 1 registered
[ 0.095818] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.095871] PTP clock support registered
[ 0.096438] Advanced Linux Sound Architecture Driver Initialized.
[ 0.097484] Bluetooth: Core ver 2.22
[ 0.097619] NET: Registered protocol family 31
[ 0.097641] Bluetooth: HCI device and connection manager initialized
[ 0.097670] Bluetooth: HCI socket layer initialized
[ 0.097707] Bluetooth: L2CAP socket layer initialized
[ 0.097779] Bluetooth: SCO socket layer initialized
[ 0.098923] clocksource: Switched to clocksource timer@f0010000
[ 0.124810] NET: Registered protocol family 2
[ 0.125874] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[ 0.126003] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.126065] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.126117] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.126348] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.126399] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.126784] NET: Registered protocol family 1
[ 0.127905] RPC: Registered named UNIX socket transport module.
[ 0.127934] RPC: Registered udp transport module.
[ 0.127947] RPC: Registered tcp transport module.
[ 0.127960] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.130155] Initialise system trusted keyrings
[ 0.130641] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.131453] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.145829] Key type asymmetric registered
[ 0.145860] Asymmetric key parser 'x509' registered
[ 0.145907] io scheduler noop registered (default)
[ 0.145925] io scheduler mq-deadline registered
[ 0.145941] io scheduler kyber registered
[ 0.163411] brd: module loaded
[ 0.181416] loop: module loaded
[ 0.182770] atmel_usart_serial.0.auto: ttyS1 at MMIO 0xf001c000 (irq = 23, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.184681] atmel_usart_serial.1.auto: ttyS2 at MMIO 0xf0020000 (irq = 24, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.186520] atmel_usart_serial.2.auto: ttyS5 at MMIO 0xf0024000 (irq = 25, base_baud = 4125000) is a ATMEL_SERIAL
[ 0.188391] atmel_usart_serial.3.auto: ttyS0 at MMIO 0xffffee00 (irq = 38, base_baud = 8250000) is a ATMEL_SERIAL
[ 0.854638] console [ttyS0] enabled
[ 0.863662] atmel_spi f0004000.spi: Using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers
[ 0.873064] atmel_spi f0004000.spi: Atmel SPI Controller version 0x213 at 0xf0004000 (irq 20)
[ 0.883172] atmel_spi f8008000.spi: Using dma1chan0 (tx) and dma1chan1 (rx) for DMA transfers
[ 0.892540] atmel_spi f8008000.spi: Atmel SPI Controller version 0x213 at 0xf8008000 (irq 28)
[ 0.902353] libphy: Fixed MDIO Bus: probed
[ 0.907235] CAN device driver interface
[ 0.912701] at91_can f000c000.can: device registered (reg_base=(ptrval), irq=45)
[ 0.922422] libphy: MACB_mii_bus: probed
[ 1.021209] Micrel KSZ9031 Gigabit PHY f0028000.ethernet-ffffffff:07: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=f0028000.ethernet-ffffffff:07, irq=POLL)
[ 1.037163] macb f0028000.ethernet eth0: Cadence GEM rev 0x00020119 at 0xf0028000 irq 46 (00:10:a1:98:97:01)
[ 1.048394] libphy: MACB_mii_bus: probed
[ 1.150529] Micrel KSZ8081 or KSZ8091 f802c000.ethernet-ffffffff:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=f802c000.ethernet-ffffffff:01, irq=POLL)
[ 1.166304] macb f802c000.ethernet eth1: Cadence MACB rev 0x0001010c at 0xf802c000 irq 47 (00:10:a1:98:97:02)
[ 1.176663] PPP generic driver version 2.4.2
[ 1.181433] PPP MPPE Compression module registered
[ 1.186185] NET: Registered protocol family 24
[ 1.190756] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.197250] ehci-atmel: EHCI Atmel driver
[ 1.205559] atmel-ehci 700000.ehci: EHCI Host Controller
[ 1.210986] atmel-ehci 700000.ehci: new USB bus registered, assigned bus number 1
[ 1.219200] atmel-ehci 700000.ehci: irq 50, io mem 0x00700000
[ 1.249009] atmel-ehci 700000.ehci: USB 2.0 started, EHCI 1.00
[ 1.255259] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 1.263578] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.270818] usb usb1: Product: EHCI Host Controller
[ 1.275660] usb usb1: Manufacturer: Linux 4.19.78-tano-at91-standard-g046113c438-tano0.2.20.20.0.0 ehci_hcd
[ 1.285503] usb usb1: SerialNumber: 700000.ehci
[ 1.291388] hub 1-0:1.0: USB hub found
[ 1.295194] hub 1-0:1.0: 3 ports detected
[ 1.300641] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.306841] ohci-atmel: OHCI Atmel driver
[ 1.312210] at91_ohci 600000.ohci: USB Host Controller
[ 1.317382] at91_ohci 600000.ohci: new USB bus registered, assigned bus number 2
[ 1.325278] at91_ohci 600000.ohci: irq 50, io mem 0x00600000
[ 1.403383] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 1.411717] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.418958] usb usb2: Product: USB Host Controller
[ 1.423710] usb usb2: Manufacturer: Linux 4.19.78-tano-at91-standard-g046113c438-tano0.2.20.20.0.0 ohci_hcd
[ 1.433527] usb usb2: SerialNumber: at91
[ 1.439662] hub 2-0:1.0: USB hub found
[ 1.443476] hub 2-0:1.0: 3 ports detected
[ 1.449223] usbcore: registered new interface driver cdc_acm
[ 1.454853] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.463156] usbcore: registered new interface driver usb-storage
[ 1.469440] usbcore: registered new interface driver usbserial_generic
[ 1.476011] usbserial: USB Serial support registered for generic
[ 1.482141] usbcore: registered new interface driver ftdi_sio
[ 1.487917] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 1.496793] at91_rtc fffffeb0.rtc: registered as rtc0
[ 1.501930] at91_rtc fffffeb0.rtc: AT91 Real Time Clock driver.
[ 1.508049] i2c /dev entries driver
[ 1.514467] at91-reset fffffe00.rstc: Starting after wakeup
[ 1.521647] Bluetooth: HCI UART driver ver 2.3
[ 1.526052] Bluetooth: HCI UART protocol H4 registered
[ 1.531392] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 1.537774] usbcore: registered new interface driver btusb
[ 1.543861] sdhci: Secure Digital Host Controller Interface driver
[ 1.550086] sdhci: Copyright(c) Pierre Ossman
[ 1.555296] atmel_mci f0000000.mmc: version: 0x505
[ 1.561284] atmel_mci f0000000.mmc: using dma0chan6 for DMA transfers
[ 1.567944] atmel_mci f0000000.mmc: Linked as a consumer to regulator.1
[ 1.600469] atmel_mci f0000000.mmc: Atmel MCI controller at 0xf0000000 irq 19, 1 slots
[ 1.609287] atmel_mci f8000000.mmc: version: 0x505
[ 1.614604] atmel_mci f8000000.mmc: using dma1chan2 for DMA transfers
[ 1.646968] atmel_mci f8000000.mmc: Atmel MCI controller at 0xf8000000 irq 27, 1 slots
[ 1.655289] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.662566] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.669000] atmel_aes f8038000.aes: version: 0x135
[ 1.677494] atmel_aes f8038000.aes: Atmel AES - Using dma1chan3, dma1chan4 for DMA transfers
[ 1.686717] atmel_sha f8034000.sha: version: 0x410
[ 1.692107] atmel_sha f8034000.sha: using dma1chan5 for DMA transfers
[ 1.700310] atmel_sha f8034000.sha: Atmel SHA1/SHA256/SHA224/SHA384/SHA512
[ 1.707876] atmel_tdes f803c000.tdes: version: 0x701
[ 1.713720] atmel_tdes f803c000.tdes: using dma1chan6, dma1chan7 for DMA transfers
[ 1.725849] atmel_tdes f803c000.tdes: Atmel DES/TDES
[ 1.731570] usbcore: registered new interface driver usbhid
[ 1.737108] usbhid: USB HID core driver
[ 1.745622] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.752030] nand: Micron MT29F2G08ABAEAWP
[ 1.756000] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.764648] Bad block table found at page 131008, version 0x01
[ 1.771087] Bad block table found at page 130944, version 0x01
[ 1.777305] 7 fixed-partitions partitions found on MTD device atmel_nand
[ 1.784039] Creating 7 MTD partitions on "atmel_nand":
[ 1.789191] 0x000000000000-0x000000040000 : "at91bootstrap"
[ 1.796784] 0x000000040000-0x000000180000 : "uboot"
[ 1.803769] 0x000000180000-0x0000001c0000 : "startup"
[ 1.810821] 0x0000001c0000-0x000000200000 : "ubootenv"
[ 1.817873] 0x000000200000-0x000006a00000 : "system_a"
[ 1.827233] 0x000006a00000-0x00000d200000 : "system_b"
[ 1.836507] 0x00000d200000-0x000010000000 : "rootfs_data"
[ 1.845996] iio iio:device0: Resolution used: 12 bits
[ 1.851123] iio iio:device0: ADC Touch screen is disabled.
[ 1.862187] u32 classifier
[ 1.864848] Actions configured
[ 1.868854] NET: Registered protocol family 10
[ 1.875518] Segment Routing with IPv6
[ 1.879367] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 1.886487] NET: Registered protocol family 17
[ 1.891160] Bridge firewalling registered
[ 1.895124] can: controller area network core (rev 20170425 abi 9)
[ 1.901590] NET: Registered protocol family 29
[ 1.906049] can: raw protocol (rev 20170425)
[ 1.910333] can: broadcast manager protocol (rev 20170425 t)
[ 1.915975] can: netlink gateway (rev 20170425) max_hops=1
[ 1.921977] Bluetooth: RFCOMM TTY layer initialized
[ 1.926846] Bluetooth: RFCOMM socket layer initialized
[ 1.932121] Bluetooth: RFCOMM ver 1.11
[ 1.935843] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.941201] Bluetooth: BNEP filters: protocol multicast
[ 1.946400] Bluetooth: BNEP socket layer initialized
[ 1.951404] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.957303] Bluetooth: HIDP socket layer initialized
[ 1.962380] l2tp_core: L2TP core driver, V2.0
[ 1.966711] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.971540] l2tp_netlink: L2TP netlink interface
[ 1.978021] Loading compiled-in X.509 certificates
[ 1.991609] ubi0: default fastmap pool size: 40
[ 1.996102] ubi0: default fastmap WL pool size: 20
[ 2.000985] ubi0: attaching mtd4
[ 2.008061] random: fast init done
[ 2.559147] ubi0: scanning is finished
[ 2.573107] ubi0: attached mtd4 (name "system_a", size 104 MiB)
[ 2.579086] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.585926] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.592780] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.599754] ubi0: good PEBs: 832, bad PEBs: 0, corrupted PEBs: 0
[ 2.605738] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 2.613024] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1316010412
[ 2.622184] ubi0: available PEBs: 560, total reserved PEBs: 272, PEBs reserved for bad PEB handling: 40
[ 2.631641] ubi0: background thread "ubi_bgt0d" started, PID 88
[ 2.637575] ubi1: default fastmap pool size: 15
[ 2.642108] ubi1: default fastmap WL pool size: 7
[ 2.646772] ubi1: attaching mtd6
[ 2.910780] ubi1: scanning is finished
[ 2.923364] ubi1: attached mtd6 (name "rootfs_data", size 46 MiB)
[ 2.929527] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.936371] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.943222] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.950198] ubi1: good PEBs: 364, bad PEBs: 4, corrupted PEBs: 0
[ 2.956181] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 2.963465] ubi1: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1965366693
[ 2.972640] ubi1: available PEBs: 0, total reserved PEBs: 364, PEBs reserved for bad PEB handling: 36
[ 2.983979] ubi1: background thread "ubi_bgt1d" started, PID 89
[ 2.990909] block ubiblock0_1: created from ubi0:1(rootfs)
[ 2.997636] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 3.005286] at91_rtc fffffeb0.rtc: setting system clock to 2007-01-01 00:00:11 UTC (1167609611)
[ 3.014897] ALSA device list:
[ 3.017819] No soundcards found.
[ 3.026284] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.036279] devtmpfs: mounted
[ 3.042215] Freeing unused kernel memory: 1024K
[ 3.046984] Run /sbin/init as init process
[ 3.273314] init: Console is alive
[ 4.050502] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.069195] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.078163] init: - preinit -
[ 4.156803] random: crng init done
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.159398] SWUPDATE: AT91Bootstrap version 3.10.1-rc1-gitAUTOINC+1d013b417b-r0.tano1
[ 8.523676] SWUPDATE: U-Boot version 2020.01-gitAUTOINC+af59b26c22-tano0.2
[ 8.599988] SWUPDATE: U-Boot startup version 1.0.0-tano1.atmel1
[ 8.626986] SWUPDATE: Kernel version 4.19.78-tano-at91-standard-g046113c438-tano0.2.20.20.0.0
[ 8.647876] SWUPDATE: Read-only filesystem version 2022-08-10-00-04-17-UTC
[ 8.844265] mount_root: loading kmods from internal overlay
[ 8.982880] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 8.992691] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 9.180246] UBIFS (ubi1:0): default file-system created
[ 9.186410] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 175
[ 9.278346] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "rootfs_data"
[ 9.286246] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 9.296195] UBIFS (ubi1:0): FS size: 39616512 bytes (37 MiB, 312 LEBs), journal size 2031616 bytes (1 MiB, 16 LEBs)
[ 9.306657] UBIFS (ubi1:0): reserved for root: 1871185 bytes (1827 KiB)
[ 9.313287] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID F15CCBFF-07A1-4518-B252-915139466F5D, small LPT model
[ 9.325670] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 9.332996] block: unable to load configuration (fstab: Entry not found)
[ 9.339941] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 9.346609] block: unable to load configuration (fstab: Entry not found)
[ 9.353543] block: attempting to load /etc/config/fstab
[ 9.363607] block: extroot: not configured
[ 9.371163] UBIFS (ubi1:0): un-mount UBI device 1
[ 9.376124] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" stops
[ 9.388296] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 176
[ 9.478293] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "rootfs_data"
[ 9.486198] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 9.496147] UBIFS (ubi1:0): FS size: 39616512 bytes (37 MiB, 312 LEBs), journal size 2031616 bytes (1 MiB, 16 LEBs)
[ 9.506608] UBIFS (ubi1:0): reserved for root: 1871185 bytes (1827 KiB)
[ 9.513239] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID F15CCBFF-07A1-4518-B252-915139466F5D, small LPT model
[ 9.660176] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 9.667360] block: unable to load configuration (fstab: Entry not found)
[ 9.674317] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 9.681086] block: unable to load configuration (fstab: Entry not found)
[ 9.687934] block: attempting to load /etc/config/fstab
[ 9.694008] block: extroot: not configured
[ 9.700671] mount_root: overlay filesystem has not been fully initialized yet
[ 9.708574] mount_root: switching to ubifs overlay
[ 9.874156] Root filesystem mounted
[ 11.538087] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 11.608260] procd: - ubus -
[ 11.675650] procd: - init -
Please press Enter to activate this console.
[ 15.011001] kmodloader: loading kernel modules from /etc/modules.d/*
[ 15.043459] tun: Universal TUN/TAP device driver, 1.6
[ 15.128442] atmel_usba_udc 500000.gadget: MMIO registers at [mem 0xf8030000-0xf8033fff] mapped at 6d8a1055
[ 15.138281] atmel_usba_udc 500000.gadget: FIFO at [mem 0x00500000-0x005fffff] mapped at a5b59dff
[ 15.180927] usbcore: registered new interface driver cdc_wdm
[ 15.226413] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 15.443690] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 15.450893] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 15.459576] cfg80211: failed to load regulatory.db
[ 15.480835] cryptodev: loading out-of-tree module taints kernel.
[ 15.499530] cryptodev: driver 1.12 loaded.
[ 15.504796] gre: GRE over IPv4 demultiplexor driver
[ 15.605130] PPTP driver version 0.8.5
[ 15.644785] xt_time: kernel timezone is +0300
[ 15.661935] usbcore: registered new interface driver cdc_ncm
[ 15.709169] usbcore: registered new interface driver qmi_wwan
[ 15.738349] usbcore: registered new interface driver cdc_mbim
[ 15.763946] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 28.043560] udevd[1365]: starting version 3.2.10
[ 28.181549] udevd[1365]: starting eudev-3.2.10
[ 75.439646] br-lan: port 1(eth0) entered blocking state
[ 75.444843] br-lan: port 1(eth0) entered disabled state
[ 75.450706] device eth0 entered promiscuous mode
[ 75.529425] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 75.614124] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 97.370138] using random self ethernet address
[ 97.374549] using random host ethernet address
[ 97.380572] usb0: HOST MAC 5a:91:66:73:af:9b
[ 97.384953] usb0: MAC b6:f1:41:3f:59:95
[ 97.388823] using random self ethernet address
[ 97.393310] using random host ethernet address
[ 97.397838] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[ 97.404482] g_ether gadget: g_ether ready
[ 97.413199] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
[ 97.578887] g_ether gadget: high-speed config #2: RNDIS
[ 97.584431] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready
tanowrt login: root
Password:
_______ __ __ _
|__ __| \ \ / / | | Embedded Linux Distribution
| | __ _ _ __ __\ \ /\ / / __| |_ by Tano Systems
| |/ _` | '_ \ / _ \ \/ \/ / '__| __|
| | (_| | | | | (_) \ /\ /| | | |_ (c) 2018-2022 Tano Systems LLC
|_|\__,_|_| |_|\___/ \/ \/ |_| \__| https://tano-systems.com
Board: Atmel SAMA5D3 Xplained (NAND)
Release: 2021.06
Revision: 14d1bbc7f5ec17202202096cb34890d3446b68be
2022-08-10 00:04:17 UTC
[root@tanowrt ~]#